首頁 收藏 QQ群
 網站導航

ZNDS智能電視網 推薦當貝市場

TV應用下載 / 資源分享區

軟件下載 | 游戲 | 討論 | 電視計算器

綜合交流 / 評測 / 活動區

交流區 | 測硬件 | 網站活動 | Z幣中心

新手入門 / 進階 / 社區互助

新手 | 你問我答 | 免費刷機救磚 | ROM固件

查看: 340354|回復: 26
上一主題 下一主題
[咪咕]

咪咕盒子MG101固件

  [復制鏈接]
跳轉到指定樓層
樓主
發表于 2017-6-5 08:55 | 只看該作者 回帖獎勵 |倒序?yàn)g覽 |閱讀模式 | 來自河南
咪咕盒子MG101-U7-HN,內存1G,硬盤4G,CPU 4核,海思3798MV100 ,系統安卓4.4.2
TTL連接后,超級終端(PUTTY,SecureCRT等)跑碼是亂碼,測量GND-RX,GND-TX電壓為0伏,0.05伏,正常應該為3.3伏左右。因此無法打開ADB。
盒子目前無可用的卡刷包,無法通短接CPU1,2角卡刷。端口掃描器掃描的端口為:33896.但無法連接。
hitool工具無法與盒子正常連接。附:最新K4刷機http://pan.baidu.com/s/1pLJOZ5D
TTL打開ADB方法:http://pan.baidu.com/s/1qYDHu0W
超級終端(SecureCRT)跑碼:
Bootrom start
Boot from eMMC
Starting fastboot ...

System startup
DDRS
Reg Version:  v1.1.0
Reg Time:     2016-12-13 14:04:40
Reg Name:     hi3798mdmo1g_hi3798mv100_ddr3_768mbyte_16bitx2_4layers_emmc.reg
Jump to DDR

Fastboot 3.3.0-dirty (compile@tmajor) (Jan 15 2017 - 08:55:57)
Fastboot:      Version 3.3.0
Build Date:    Jan 15 2017, 08:57:11
CPU:           Hi3798Mv100
Boot Media:    eMMC
DDR Size:      1GB
Check nand flash controller v610. found
Special NAND id table Version 1.36
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found!!!
MMC/SD controller initialization.
MMC/SD Card:
     MID:         0x15
     Read Block:  512 Bytes
     Write Block: 512 Bytes
     Chip Size:   7456M Bytes (High Capacity)
     Name:        "8GME4"
     Chip Type:   MMC
     Version:     4.0
     Speed:       52000000Hz
     Bus Width:   8bit
     Boot Addr:   0 Bytes
Boot Env on eMMC
     Env Offset:          0x00100000
     Env Size:            0x00010000
     Env Range:           0x00010000
HI_OTP_LockIdWord,327: ID_WORD have already been locked

SDK Version: HiSTBAndroidV600R001C00SPC064_v2016060803
press the key!!
get key 0 2
get chipid =137980100
get chipType (HI3798MV100)
count=5
get chipid =137980100
get chipType (HI3798MV100)
count=5
entry_module===kernel
entry_factory_flag == 0
termflag = 0
--termflag:0,devicenumflag:1,devicenumlen:11,deviceid_len:15,stbmac:004703000003731000083C0CDB005A76
[STB_INFO] SN:004703000003731000083C0CDB005A76111003310878750MG100-U7_HN
[STB_INFO] MAC: 3C0CDB005A76
[STB_INFO] deviceid: 111003310878750
um_mac:3C0CDB005A76
um_serial:004703000003731000083C0CDB005A76
um_deviceid:111003310878750
[um_set_mac]MAC :[3C:0C:DB:00:5A:76]  now set ethaddr.
str_serial:004703000003731000083C0CDB005A76
str_deviceid:111003310878750
Reserve Memory
     Start Addr:          0x2FFFE000
     Bound Addr:          0x8D32000
     Free  Addr:          0x2ED48000
     Alloc Block:  Addr        Size
                   0x2FBFD000       4194304
                   0x2F8FC000       3145728
                   0x2F87B000       524288
                   0x2F878000       8192
                   0x2F843000       212992
                   0x2F742000       1048576
                   0x2F73E000       12288
                   0x2F3B9000       3686400
                   0x2F223000       1658880
                   0x2EE9E000       3686400
                   0x2ED4B000       1384448
                   0x2ED48000       8192
Hibernate!! drv  phyaddr 0x2FC00000
Hibernate!! user api phyaddr 0x2F900000
Hibernate!! userapi  start 0x14B00000, size 0x800000
Hibernate!! drv  start 0x15300000, size 0x800000
Hibernate!! flag start 0x15B00000, size 0x800000
Hibernate!! data start 0x16300000, size 0x12C00000
Press Ctrl+C to stop autoboot
MMC read: dev # 0, block # 327680, count 20480 ... 20480 blocks read: OK
86794984 Bytes/s
Found Initrd at 0x04000000 (Size 652813 Bytes), align at 16384 Bytes
## Booting kernel from Legacy Image at 01ffffc0 ...
    Image Name:   Linux-3.10.0_s40
    Image Type:   ARM Linux Kernel Image (uncompressed)
    Data Size:    7858928 Bytes = 7.5 MiB
    Load Address: 02000000
    Entry Point:  02000000
    XIP Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 3.10.0_s40 (compile@tmajor) (gcc version 4.4.1 (Hisilicon_v200(gcc4.4-290+glibc-2.11+eabi+nptl)) ) #1 SMP Sun Jan 15 09:04:02 HKT 2017
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: bigfish
cma: CMA: reserved 300 MiB at 0d400000
cma: CMA: reserved 4 MiB at 2fc00000
Memory policy: ECC disabled, Data cache writealloc
CPU: Hi3798Mv100
PERCPU: Embedded 8 pages/cpu @81894000 s12224 r8192 d12352 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 195072
Kernel command line: console=ttyAMA0,115200 blkdevparts=mmcblk0:1M(fastboot),1M(bootargs),10M(recovery),2M(deviceinfo),8M(baseparam),8M(pqparam),20M(logo),20M(logobak),10M(loaderdb),40M(fastplay),40M(fastplaybak),40M(kernel),20M(misc),1M(stbid),10M(fackernel),100M(facrootbox),8M(userapi),8M(hibdrv),8M(qbflag),300M(qbdata),600M(cache),700M(system),50M(keydata),-(userdata) coherent_pool=1M androidboot.serialno=004703000003731000083C0CDB005A76 androidboot.deviceid=111003310878750 initrd=0x4000000,0x9F60D mem=768M mmz=ddr,0,212M,300M
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 768MB = 768MB total
Memory: 442040k/442040k available, 344392k reserved, 0K highmem
Virtual kernel memory layout:
     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
     vmalloc : 0xb0800000 - 0xff000000   (1256 MB)
     lowmem  : 0x80000000 - 0xb0000000   ( 768 MB)
     pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
     modules : 0x7f000000 - 0x7fe00000   (  14 MB)
       .text : 0x80008000 - 0x80ee934c   (15237 kB)
       .init : 0x80eea000 - 0x80f5afc0   ( 452 kB)
       .data : 0x80f5c000 - 0x810a5008   (1317 kB)
        .bss : 0x810a5008 - 0x8128d25c   (1953 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:192
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
Console: colour dummy device 80x30
Calibrating delay loop... 1949.69 BogoMIPS (lpj=974848)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
ftrace: allocating 33093 entries in 98 pages
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x80b32de8 - 0x80b32e40
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
Brought up 4 CPUs
SMP: Total of 4 processors activated (7829.50 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
[110 ERROR-Invalid]:MCE_Init[2135]:ERR: get PDM Param
NET: Registered protocol family 16
DMA: preallocated 1024 KiB pool for atomic coherent allocations
hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 8 bytes.
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0xf8b00000 (irq = 81) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0xf8006000 (irq = 82) is a PL011 rev2
uart:2: ttyAMA2 at MMIO 0xf8b02000 (irq = 83) is a PL011 rev2
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux video capture interface: v2.00
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Switching to clocksource timer3
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 636K (84000000 - 8409f000)
NetWinder Floating Point Emulator V0.97 (double precision)
CPU PMU: probing PMU on CPU 0
hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. (NAND) ? 2001-2006 Red Hat, Inc.
fuse init (API version 7.22)
msgmni has been set to 1472
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
brd: module loaded
loop: module loaded
input: Hi keyboard as /devices/virtual/input/input0
input: Hi mouse as /devices/virtual/input/input1
input: qwerty as /devices/virtual/input/input2
Hi Android vinput driver init successful!
Found Nand Flash Controller V610.
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
libphy: himii: probed
Up port phy at 0x01 is connect
libphy: PHY himii:1f not found
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
usbotg: usb otg driver registeredusbcore: registered new interface driver cdc_wdm
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver usbserial
usbcore: registered new interface driver option
usbserial: USB Serial support registered for GSM modem (1-port)
dwc_otg: version 3.00a 10-AUG-2012
Core Release: 3.10a
Setting default values for core params
Using Buffer DMA mode
Dedicated Tx FIFOs mode
g_ffs: file system registered
mousedev: PS/2 mouse device common for all mice
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
mmc0: BKOPS_EN bit is not set
mmc0: new high speed DDR MMC card at address 0001
mmcblk0: mmc0:0001 8GME4R 7.28 GiB
mmcblk0boot0: mmc0:0001 8GME4R partition 1 4.00 MiB
mmcblk0boot1: mmc0:0001 8GME4R partition 2 4.00 MiB
mmcblk0: p1(fastboot) p2(bootargs) p3(recovery) p4(deviceinfo) p5(baseparam) p6(pqparam) p7(logo) p8(logobak) p9(loaderdb) p10(fastplay) p11(fastplaybak) p12(kernel) p13(misc) p14(stbid) p15(fackernel) p16(facrootbox) p17(userapi) p18(hibdrv) p19(qbflag) p20(qbdata) p21(cache) p22(system) p23(keydata) p24(userdata)
mmcblk0boot1: unknown partition table
mmcblk0boot0: unknown partition table
hidraw: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
zram: Created 1 device(s) ...
ashmem: initialized
logger: created 256K log 'log_main'
logger: created 256K log 'log_events'
logger: created 256K log 'log_radio'
logger: created 256K log 'log_system'
Mali: Mali device driver loaded
usbcore: registered new interface driver snd-usb-audio
oprofile: using timer interrupt.
GACT probability on
Mirror/redirect action on
Failed to load ipt action
Simple TC action Loaded
netem: version 1.3
u32 classifier
     Performance counters on
     input device check on
     Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (11780 buckets, 47120 max)
ctnetlink v0.93: registering with nfnetlink.
NF_TPROXY: Transparent proxy support initialized, version 4.1.0
NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
xt_time: kernel timezone is -0000
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: Creating netns size=776 id=0
IPVS: ipvs loaded.
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP: cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
Bridge firewalling registered
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: BNEP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: HIDP socket layer initialized
8021q: 802.1Q VLAN Support v1.8
lib80211: common routines for IEEE802.11 drivers
VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
Load hi_tde.ko success.         (SDK_VERSION:[HiSTBAndroidV600R001C00SPC064_v2016060803] Build Time:[Jan 15 2017, 09:03:23])
Load hi_fb.ko success.  (SDK_VERSION:[HiSTBAndroidV600R001C00SPC064_v2016060803] Build Time:[Jan 15 2017, 09:03:02])
DieID is locked!
hisi-sndcard hisi-sndcard:  aiao-hifi <-> hisi-i2s mapping ok
Load hi_png.ko success.         (SDK_VERSION:[HiSTBAndroidV600R001C00SPC064_v2016060803] Build Time:[Jan 15 2017, 09:03:15])
Load hi_jpegenc.ko success.     (SDK_VERSION:[HiSTBAndroidV600R001C00SPC064_v2016060803] Build Time:[Jan 15 2017, 09:03:05])
enter temperature_control_thread
ALSA device list:
   #0: HISI-AIAO
Freeing unused kernel memory: 448K (80eea000 - 80f5a000)
init: /init.bigfish.rc: 82: invalid option 'sdcard_r'
init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
init: load loaderdb finish!
init: start set ro.product.model:MG100-U7_HN
init: start set ro.build.product:MG100-U7_HN
init: /dev/hw_random not found
init: cannot open '/initlogo.rle'
init: Start mount system t:2
EXT4-fs (mmcblk0p22): mounted filesystem with ordered data mode. Opts: (null)
init: End mount t:2
init: Start mount userdata t:2
init: firstboot:1
EXT4-fs (mmcblk0p24): recovery complete
EXT4-fs (mmcblk0p24): mounted filesystem with ordered data mode. Opts: (null)
init: End mount t:2
init: Start mount cache t:2
EXT4-fs (mmcblk0p21): recovery complete
EXT4-fs (mmcblk0p21): mounted filesystem with ordered data mode. Opts: (null)
init: End mount t:2
init: Start mount keydata t:2
EXT4-fs (mmcblk0p23): recovery complete
EXT4-fs (mmcblk0p23): mounted filesystem with ordered data mode. Opts: (null)
init: End mount t:2
init: /dev/hw_random not found
healthd: No charger supplies found
init: cannot find '/system/bin/rild', disabling 'ril-daemon'
init: cannot find '/system/bin/dbus-daemon', disabling 'dbus'
init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
init: cannot find '/system/bin/mtkbt', disabling 'blueangel'
init: cannot find '/system/bin/dtvserver', disabling 'dtvserver'
init: cannot find '/system/bin/gpio-led', disabling 'gpio-led'
init: cannot find '/system/bin/hidns-sd', disabling 'hidns-sd'
init: cannot find '/system/bin/usb-driver', disabling 'usb-driver'
init: property 'sys.powerctl' doesn't exist while expanding '${sys.powerctl}'
init: powerctl: cannot expand '${sys.powerctl}'
init: property 'sys.sysctl.extra_free_kbytes' doesn't exist while expanding '${sys.sysctl.extra_free_kbytes}'
init: cannot expand '${sys.sysctl.extra_free_kbytes}' while writing to '/proc/sys/vm/extra_free_kbytes'
healthd: BatteryStatusPath not found
healthd: BatteryHealthPath not found
healthd: BatteryPresentPath not found
healthd: BatteryCapacityPath not found
healthd: BatteryVoltagePath not found
healthd: BatteryTemperaturePath not found
healthd: BatteryTechnologyPath not found

Welcome to HiAndroid

enter low_ram mode

Adding 102396k swap on /dev/block/zram0.  Priority:-1 extents:1 across:102396k SS
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
hiusb-ehci hiusb-ehci.0: HIUSB EHCI
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
hiusb-ehci hiusb-ehci.0: irq 98, io mem 0xf9890000
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hiusb-ehci hiusb-ehci.1: HIUSB EHCI
hiusb-ehci hiusb-ehci.1: new USB bus registered, assigned bus number 2
hiusb-ehci hiusb-ehci.1: irq 94, io mem 0xf9930000
hiusb-ehci hiusb-ehci.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
hiusb-ohci hiusb-ohci.0: HIUSB OHCI
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 3
hiusb-ohci hiusb-ohci.0: irq 99, io mem 0xf9880000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hiusb-ohci hiusb-ohci.1: HIUSB OHCI
hiusb-ohci hiusb-ohci.1: new USB bus registered, assigned bus number 4
hiusb-ohci hiusb-ohci.1: irq 95, io mem 0xf9920000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
rtk_btusb: Realtek Bluetooth USB driver module init, version 3.0
rtk_btusb: Register usb char device interface for BT driver
usbcore: registered new interface driver rtk_btusb
tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel.
Disabling lock debugging due to kernel taint
usb 1-2: new high-speed USB device number 2 using hiusb-ehci
Tuxera NTFS driver 3015.1.29.1.1 [Flags: R/W MODULE].
create enforce
warning: `zygote' uses 32-bit capabilities (legacy support in use)
lowmemorykiller: lowmem_shrink: convert oom_adj to oom_score_adj:
lowmemorykiller: oom_adj 0 => oom_score_adj 0
lowmemorykiller: oom_adj 1 => oom_score_adj 58
lowmemorykiller: oom_adj 2 => oom_score_adj 117
lowmemorykiller: oom_adj 3 => oom_score_adj 176
lowmemorykiller: oom_adj 9 => oom_score_adj 529
lowmemorykiller: oom_adj 15 => oom_score_adj 1000
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
cfg80211: Calling CRDA to update world regulatory domain
RTL871X: module init start
RTL871X: rtl8188eu v4.3.0.8_13968.20150417
RTL871X: build time: Jan 15 2017 09:04:25
bFWReady == _FALSE call reset 8051...
RTL871X: rtw_ndev_init(wlan0)
RTL871X: rtw_ndev_init(p2p0)
usbcore: registered new interface driver rtl8188eu
RTL871X: module init ret=0
IPv6: ADDRCONF(NETDEV_UP): p2p0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
RTL871X: rtw_set_802_11_connect(wlan0)  fw_state=0x00000008
RTL871X: start auth
RTL871X: auth success, start assoc
RTL871X: assoc success
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
RsvdPageNum: 8
RTL871X: recv eapol packet
RTL871X: send eapol packet
RTL871X: recv eapol packet
RTL871X: send eapol packet
RTL871X: set pairwise key camid:4, addr:d8:15:0d:7d:dc:d4, kid:0, type:AES
RTL871X: set group key camid:5, addr:d8:15:0d:7d:dc:d4, kid:1, type:AES
binder: 1413:1413 BC_REQUEST_DEATH_NOTIFICATION death notification already set
求神指點,跪謝,跪謝。。。 咪咕盒子MG101固件

咪咕盒子MG101固件

咪咕盒子MG101固件



上一篇:咪咕盒子MG100-U7-HN(1G+4G)
下一篇:九聯UNT400C刷機包及方法 同烽火HG680-R
沙發
發表于 2017-6-5 09:16 | 只看該作者 | 來自河南
可以刷機,不過我的刷完無線不好用了
板凳
發表于 2017-6-14 11:31 來自ZNDS手機版 | 只看該作者 | 來自四川
fxzh1987 發表于 2017-6-5 09:16
可以刷機,不過我的刷完無線不好用了

樓主能不能把你的咪咕mg100原廠固件備份分享給我啊
地板
發表于 2017-6-15 14:48 來自ZNDS手機版 | 只看該作者 | 來自廣西
這只是輸出的信息,輸入的找不到
5#
發表于 2017-6-15 14:48 來自ZNDS手機版 | 只看該作者 | 來自廣西
我有刷機固件
6#
發表于 2017-6-15 14:53 | 只看該作者 | 來自廣西
https://yun.baidu.com/wap/share/home?&uk=890608562&errno=0&errmsg=Auth%20Login%20Sucess&&bduss=&ssnerror=0#category/type=0
7#
發表于 2017-6-15 14:53 | 只看該作者 | 來自廣西
這就是,刷好告訴我怎么刷
8#
發表于 2017-6-16 08:02 | 只看該作者 | 來自四川
0012025 發表于 2017-6-15 14:53
這就是,刷好告訴我怎么刷

那個是mg100的包啊
9#
發表于 2017-6-20 08:03 來自ZNDS手機版 | 只看該作者 | 來自廣西
https://yun.baidu.com/wap/link?uk=890608562&third=0&shareid=2719794257#list/path=%2F%E4%B8%AD%E5%9B%BD%E7%A7%BB%E5%8A%A8%E9%9B%86%E9%87%873798M-0912%E7%89%88%E6%9C%AC%2F2016-09-12%2F%E7%99%BE%E8%A7%86%E9%80%9A%E7%89%88%E6%9C%AC%2FEmmc&page=1
10#
發表于 2017-8-18 11:49 | 只看該作者 | 來自廣西
學習學習!
11#
發表于 2017-9-15 13:12 | 只看該作者 | 來自四川
先把機器刷成磚,再把磚頭刷成機器,我都佩服自己在ZNDS學到的刷機技術!_
12#
發表于 2017-9-21 18:30 來自ZNDS手機版 | 只看該作者 | 來自重慶
0012025 發表于 2017-6-15 14:53
https://yun.baidu.com/wap/share/home?&uk=890608562&errno=0&errmsg=Auth%20Login%20Sucess&&bduss=&ssne ...

可以哦
13#
發表于 2017-10-8 21:16 | 只看該作者 | 來自廣東
請問樓主刷家成功了么有?
14#
發表于 2017-11-6 15:33 | 只看該作者 | 來自廣東
0012025 發表于 2017-6-15 14:53
https://yun.baidu.com/wap/share/home?&uk=890608562&errno=0&errmsg=Auth%20Login%20Sucess&&bduss=&ssne ...

華數版本和百事通怎么區分,我是南傳的用哪個
15#
發表于 2017-11-11 22:50 | 只看該作者 | 來自廣東
我也是南傳的,原廠icntv,有原固件

本版積分規則

Archiver|新帖|標簽|軟件|Sitemap|ZNDS智能電視網 ( 蘇ICP備2023012627號 )

網絡信息服務信用承諾書 | 增值電信業務經營許可證:蘇B2-20221768 丨 蘇公網安備 32011402011373號

GMT+8, 2024-12-22 23:07 , Processed in 0.099153 second(s), 13 queries , Redis On.

Powered by Discuz!

監督舉報:report#znds.com (請將#替換為@)

© 2007-2024 ZNDS.Com

快速回復 返回頂部 返回列表