首頁 收藏 QQ群
 網站導航

ZNDS智能電視網 推薦當貝市場

TV應用下載 / 資源分享區

軟件下載 | 游戲 | 討論 | 電視計算器

綜合交流 / 評測 / 活動區

交流區 | 測硬件 | 網站活動 | Z幣中心

新手入門 / 進階 / 社區互助

新手 | 你問我答 | 免費刷機救磚 | ROM固件

查看: 108681|回復: 15
上一主題 下一主題
[原創]

C1s更換電源IC&加裝TTL插針實錄

[復制鏈接]
跳轉到指定樓層
樓主
發表于 2016-1-12 21:46 | 只看該作者 |只看大圖 回帖獎勵 |倒序瀏覽 |閱讀模式 | 來自廣東
本帖最后由 神藍 于 2016-1-12 22:18 編輯

C1s更換電源IC&加裝TTL插針實錄

圖/文:神藍

       樂迷飛來一塊C1s磚，沒問原因，直接插電，亮一顆紅燈，通常這種情況是電源部份問題，檢測電源附近看到電源IC上有一個窟窿，八個腳把一個給燒毀了。
C1s更換電源IC&加裝TTL插針實錄



       什么也不用說，直接吹下來換，注意中間有散熱接觸部份，烙鐵是焊接不到的。（右下向上數第2腳pcb敷銅被燒毀）
C1s更換電源IC&加裝TTL插針實錄



        焊上新電源IC，把那個腳用焊錫飛好。
C1s更換電源IC&加裝TTL插針實錄



        既然動手了，給這位兄弟加上TTL插針。
C1s更換電源IC&加裝TTL插針實錄



        找來一塊舊聲卡，把插針拆下來，正合適。
C1s更換電源IC&加裝TTL插針實錄



        用烙鐵焊接好。
C1s更換電源IC&加裝TTL插針實錄



        蠻合襯的^_^
C1s更換電源IC&加裝TTL插針實錄



        插上TTL，打開終端，一串歡快的代碼結束了枯燥的維修過程。
C1s更換電源IC&加裝TTL插針實錄


  1. ?EEEE I3000000032940xf300100003877530EEEE I400000004294_M6_BL1_3003>2137333
  2. TE : 125999
  3. BT : 10:23:38 May 13 2014

  5. wait pll-0x03 target is 01d4 now it is 0x000001d3

  7. DDR clock is 468MHz with Low Power & 2T mode

  9. DDR training :
  10. DX0DLLCR:40000000
  11. DX0DQTR:ffffffff
  12. DX0DQSTR:3db05001
  13. DX1DLLCR:40000000
  14. DX1DQTR:ffffffff
  15. DX1DQSTR:3db05001
  16. DX2DLLCR:40000000
  17. DX2DQTR:ffffffff
  18. DX2DQSTR:3db05001
  19. DX3DLLCR:40000000
  20. DX3DQTR:ffffffff
  21. DX3DQSTR:3db05001
  22. Stage 00 Result 00000000

  24. aml log : Total run [1] Times

  26. HHH
  27. Boot From SPI
  28. ucl decompress...true
  29. 0x12345678
  30. Boot from internal device 1st SPI RESERVED

  32. TE : 372848
  33. System Started


  36. U-boot-00000-g4a62c80(m6_letv_g28ref@4a62c808) (May 13 2014 - 10:23:24)

  38. aml_rtc_init
  39. aml rtc init first time!
  40. Clear HDMI KSV RAM
  41. DRAM:  1 GiB
  42. relocation Offset is: 105e4000
  43. usid is: C1S5000
  44. 1 c1s board_init buf is: C1S5000
  45. 7 c1 board_init board_type is: 3
  46. 8 c1 board_init board_type is: 3
  47. NAND:  Amlogic nand flash uboot driver, Version U1.06.017 (c) 2010 Amlogic Inc.
  48. No NAND device found!!!
  49. NAND device id: 98 d7 84 93 72 57
  50. NAND device: Manufacturer ID: 0x98, Chip ID: 0x98 (Toshiba A serials NAND 4GiB TC58TEG5DCJTA00 )
  51. 1 NAND chips detected
  52. #####aml_nand_init, with RB pins and chip->chip_delay:20
  53. bus_cycle=5, bus_timing=7, start_cycle=6, end_cycle=9,system=5.0ns
  54. oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH40_1K_MODE
  55. aml_chip->oob_fill_cnt =128,aml_chip->oob_size =1280,bch_bytes =70
  56. multi plane error for selected plane mode: NAND_TWO_PLANE_MODE force plane to : NAND_SINGLE_PLANE_MODE
  57. aml_nand_init:oobmul =1,chip->ecc.layout->oobfree[0].length=32,aml_chip->oob_size=1280
  58. aml nand env valid addr: 8000
  59. key start_blk=1016,end_blk=1023,aml_nand_key_init:684
  60. aml nand key valid addr: fe000000
  61. aml nand key valid addr: fe400000
  62. aml nand key valid addr: fe800000
  63. aml nand key valid addr: fec00000
  64. CONFIG_KEYSIZE=0x10000; KEYSIZE=0xfffc; bbt=0x1330; default_keyironment_size=0xeccc
  65. i=0,register --- nand_key
  66. NAND bbt detect factory Bad block at 7b000000
  67. 2 too much bad block!!
  68. Creating 12 MTD partitions on "nandnormal":
  69. 0x000000800000-0x000001000000 : "bootargs"
  70. 0x000001000000-0x000001800000 : "misc"
  71. 0x000001800000-0x000002000000 : "baseparam"
  72. 0x000002000000-0x000002800000 : "logo"
  73. 0x000002800000-0x000003800000 : "aml_logo"
  74. 0x000003800000-0x000009800000 : "fastplay"
  75. 0x000009800000-0x00000a800000 : "recovery"
  76. 0x00000a800000-0x00000b800000 : "boot"
  77. 0x00000b800000-0x00002b800000 : "system"
  78. 0x00002b800000-0x00004b800000 : "cache"
  79. 0x00004b800000-0x00008bc00000 : "userdata"
  80. NAND bbt detect factory Bad block at 7b000000
  81. NAND bbt detect factory Bad block at 8b800000
  82. 0x00008bc00000-0x0000fe000000 : "NFTL_Part"
  83. NAND bbt detect factory Bad block at a0000000
  84. NAND bbt detect factory Bad block at a0800000
  85. NAND bbt detect factory Bad block at a1800000
  86. NAND bbt detect factory Bad block at d2000000
  87. NAND bbt detect factory Bad block at ef400000
  88. nandnormal initialized ok
  89. detect mx chiprevD :0 and nand_type: 20
  90. No NAND device found!!!
  91. NAND device id: 98 d7 84 93 72 57
  92. NAND device: Manufacturer ID: 0x98, Chip ID: 0x98 (Toshiba A serials NAND 4GiB TC58TEG5DCJTA00 )
  93. 1 NAND chips detected
  94. #####aml_nand_init, with RB pins and chip->chip_delay:20
  95. bus_cycle=5, bus_timing=7, start_cycle=6, end_cycle=9,system=5.0ns
  96. oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH40_1K_MODE
  97. aml_chip->oob_fill_cnt =128,aml_chip->oob_size =1280,bch_bytes =70
  98. multi plane error for selected plane mode: NAND_TWO_PLANE_MODE force plane to : NAND_SINGLE_PLANE_MODE
  99. aml_nand_init:oobmul =1,chip->ecc.layout->oobfree[0].length=32,aml_chip->oob_size=1280
  100. aml nand env valid addr: 8000
  101. key start_blk=1016,end_blk=1023,aml_nand_key_init:684
  102. aml nand key valid addr: fe000000
  103. aml nand key valid addr: fe400000
  104. aml nand key valid addr: fe800000
  105. aml nand key valid addr: fec00000
  106. CONFIG_KEYSIZE=0x10000; KEYSIZE=0xfffc; bbt=0x1330; default_keyironment_size=0xeccc
  107. name=nand_key nand_key
  108. NAND bbt detect factory Bad block at 7b000000
  109. 2 too much bad block!!
  110. Creating 12 MTD partitions on "nandnormal":
  111. 0x000000800000-0x000001000000 : "bootargs"
  112. 0x000001000000-0x000001800000 : "misc"
  113. 0x000001800000-0x000002000000 : "baseparam"
  114. 0x000002000000-0x000002800000 : "logo"
  115. 0x000002800000-0x000003800000 : "aml_logo"
  116. 0x000003800000-0x000009800000 : "fastplay"
  117. 0x000009800000-0x00000a800000 : "recovery"
  118. 0x00000a800000-0x00000b800000 : "boot"
  119. 0x00000b800000-0x00002b800000 : "system"
  120. 0x00002b800000-0x00004b800000 : "cache"
  121. 0x00004b800000-0x00008bc00000 : "userdata"
  122. NAND bbt detect factory Bad block at 7b000000
  123. NAND bbt detect factory Bad block at 8b800000
  124. 0x00008bc00000-0x0000fe000000 : "NFTL_Part"
  125. NAND bbt detect factory Bad block at a0000000
  126. NAND bbt detect factory Bad block at a0800000
  127. NAND bbt detect factory Bad block at a1800000
  128. NAND bbt detect factory Bad block at d2000000
  129. NAND bbt detect factory Bad block at ef400000
  130. nandnormal initialized ok
  131. detect mx chiprevD :0 and nand_type: 20
  132. nand_curr_device =0
  133. MMC:   SDIO Port B: 0, SDIO Port C: 1
  134. SPI BOOT,spi_env_relocate_spec : env_relocate_spec 53
  135. SF: Detected MX25L3205D with page size 256, total 4 MiB

  137. SPI NOR Flash have write protect!!!
  138. In:    serial
  139. Out:   serial
  140. Err:   serial
  141. register usb cfg[0] = 9fe7ef8c
  142. Net:   Meson_Ethernet
  143. init suspend firmware done. (ret:0)
  144. key_init(P_AO_RTI_PIN_MUX_REG (0xc8100014))_val = 0x9f5dbec4
  145. pre_detect_storage
  146. reboot_mode=charging
  147. ir init
  148. key_init(P_AO_RTI_PIN_MUX_REG (0xc8100014))_val = 0x9f5dbc54
  149. usid is: C1S5000
  150. 1 c1s switch_boot_mode env is: C1S5000
  151. switch_boot_mode env = C1s
  152. P_AO_RTI_STATUS_REG2: 0x0
  153. suspend = <NULL>

  155. NAND read: misc offset 0x0, size 0x2046
  156. 8262 bytes read: OK
  157. enter_recovery
  158. ### main_loop: bootcmd="run compatible_boot"
  159. Hit any key to stop autoboot:  0
  160. compatible nand
  161. Booting from nand ...

  163. NAND read: logo whole chip
  164. 8388608 bytes read: OK

  166. NAND read: boot offset 0x0, size 0x600000
  167. 6291456 bytes read: OK
  168. pre-clear hdmi ram
  169. hdcp get form storage medium: nand
  170. name=nand_key nand_key
  171. read:addr:0xfe000000,phy_blk_addr:1016,phy_page_addr:0,aml_nand_get_key:125
  172. device:nand, init key ok!!
  173. don't found keyname,uboot_key_read:1502
  174. prefetch hdcp keys from nand failed
  175. ## Booting kernel from Legacy Image at 82000000 ...
  176.    Image Name:   Linux-3.0.50-g15b99ad-dirty
  177.    Image Type:   ARM Linux Kernel Image (lzma compressed)
  178.    Data Size:    3354207 Bytes = 3.2 MiB
  179.    Load Address: 80008000
  180.    Entry Point:  80008000
  181.    Verifying Checksum ... OK
  182.         Ramdisk start addr = 0x82333800, len = 0x10b301
  183.    Uncompressing Kernel Image ... OK
  184. machid from environment: 0x4e27
  185. EFUSE machid is not set.
  186. Using machid 0x4e27 from environment

  188. Starting kernel ...

  190. [    0.000000@0] Initializing cgroup subsys cpu
  191. [    0.000000@0] Linux version 3.0.50-g15b99ad-dirty ([email]letv@letv.localhost[/email]) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #2 SMP PREEMPT Tue May 13 10:26:38 CST 2014
  192. [    0.000000@0] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7d
  193. [    0.000000@0] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
  194. [    0.000000@0] Machine: Amlogic Meson6 g02 customer platform
  195. [    0.000000@0] Ignoring unrecognised tag 0x00000000
  196. [    0.000000@0] early_mem:528: start=0x80000000, size=0x4000000
  197. [    0.000000@0] early_mem:546: start=0x91000000, size=0xef00000
  198. [    0.000000@0] early_mem:554: start=0xa0000000, size=0x20000000
  199. [    0.000000@0] Memory policy: ECC disabled, Data cache writealloc
  200. [    0.000000@0] PERCPU: Embedded 7 pages/cpu @c131f000 s5600 r8192 d14880 u32768
  201. [    0.000000@0] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 206592
  202. [    0.000000@0] Kernel command line: root=/dev/cardblksd2 rw rootfstype=ext3 rootwait init=/init console=ttyS0,115200n8 mac=c8:0e:77:02:5b:db logo=osd1,0x84100000,720p,full androidboot.resolution=720p hdmimode=720p cvbsmode=480cvbs hlt vmalloc=256m mem=1024m a9_clk_max=1512000000 vdachwswitch=component hdmitx=
  203. [    0.000000@0] ******** uboot setup mac-addr: c8:e:77:2:5b:db
  204. [    0.000000@0] osd1:1
  205. [    0.000000@0] 720p:6
  206. [    0.000000@0] full:2
  207. [    0.000000@0] kernel get hdmimode form uboot is 720p
  208. [    0.000000@0] kernel get cvbsmode form uboot is 480cvbs
  209. [    0.000000@0] HDMI DEBUG: hdmitx_boot_para_setup [1918]
  210. [    0.000000@0] PID hash table entries: 2048 (order: 1, 8192 bytes)
  211. [    0.000000@0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
  212. [    0.000000@0] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
  213. [    0.000000@0] Memory: 64MB 239MB 512MB = 815MB total
  214. [    0.000000@0] Memory: 815100k/815100k available, 19460k reserved, 524288K highmem
  215. [    0.000000@0] Virtual kernel memory layout:
  216. [    0.000000@0]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
  217. [    0.000000@0]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
  218. [    0.000000@0]     DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
  219. [    0.000000@0]     vmalloc : 0xe0000000 - 0xf0000000   ( 256 MB)
  220. [    0.000000@0]     lowmem  : 0xc0000000 - 0xdff00000   ( 511 MB)
  221. [    0.000000@0]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
  222. [    0.000000@0]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
  223. [    0.000000@0]       .init : 0xc0008000 - 0xc0037000   ( 188 kB)
  224. [    0.000000@0]       .text : 0xc0037000 - 0xc0824d2c   (8120 kB)
  225. [    0.000000@0]       .data : 0xc0826000 - 0xc087f2e0   ( 357 kB)
  226. [    0.000000@0]        .bss : 0xc087f304 - 0xc0b15be8   (2651 kB)
  227. [    0.000000@0] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  228. [    0.000000@0] Preemptible hierarchical RCU implementation.
  229. [    0.000000@0]        RCU debugfs-based tracing is enabled.
  230. [    0.000000@0] NR_IRQS:256
  231. [    0.000000@0] gic_init: irq_offset=0
  232. [    0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms
  233. [    0.000000@0] MESON TIMER-A c0839ec0
  234. [    0.000000@0] Disable timerA
  235. [    0.000000@0] Console: colour dummy device 80x30
  236. [    0.000000@0] console [ttyS0] enabled
  237. [    0.281039@0] Calibrating delay loop... 2387.14 BogoMIPS (lpj=11935744)
  238. [    0.340046@0] pid_max: default: 32768 minimum: 301
  239. [    0.342262@0] Mount-cache hash table entries: 512
  240. [    0.347529@0] Initializing cgroup subsys cpuacct
  241. [    0.351411@0] Initializing cgroup subsys freezer
  242. [    0.355988@0] CPU: Testing write buffer coherency: ok
  243. [    0.361178@0] MESON TIMER-B c0839f80
  244. [    0.364526@0] Disable timerA
  245. [    0.367383@0] Disable timerB
  246. [    0.370252@0] Disable timerA
  247. [    0.373241@0] L310 cache controller enabled
  248. [    0.377278@0] l2x0: 8 ways, CACHE_ID 0x4100a0c8, AUX_CTRL 0x7e462c01, Cache size: 524288 B
  249. [    0.385576@0]  prefetch=0x31000006
  250. [    0.388907@0] ===actlr=0x41
  251. [    0.391691@0] ===actlr=0x4b
  252. [    0.394462@0] SCU_CTRL: scu_ctrl=0x69
  253. [    0.398108@0] pl310: aux=0x7e462c01, prefetch=0x31000006
  254. [    0.501493@1] CPU1: Booted secondary processor
  255. [    0.561204@1] MESON TIMER-D c083a100
  256. [    0.561231@0] Brought up 2 CPUs
  257. [    0.561239@0] SMP: Total of 2 processors activated (4780.85 BogoMIPS).
  258. [    0.573196@1] Disable timerD
  259. [    0.576220@0] devtmpfs: initialized
  260. [    0.583452@0] clkrate [ xtal ] : 24000000
  261. [    0.583524@0] clkrate [ pll_sys ] : 1200000000
  262. [    0.587949@0] clkrate [ pll_fixed ] : 2000000000
  263. [    0.592568@0] clkrate [ pll_vid2 ] : 378000000
  264. [    0.596977@0] clkrate [ pll_hpll ] : 378000000
  265. [    0.601494@0] clkrate [ pll_ddr ] : 468000000
  266. [    0.605743@0] clkrate [ a9_clk ] : 1200000000
  267. [    0.610147@0] clkrate [ clk81 ] : 200000000
  268. [    0.614353@0] clkrate [ usb0 ] : 0
  269. [    0.617731@0] clkrate [ usb1 ] : 0
  270. [    0.622093@0] print_constraints: dummy:
  271. [    0.625076@0] NET: Registered protocol family 16
  272. [    0.630589@1] [wifi_dev_init] in
  273. [    0.632749@1] [wifi_clock_enable] in
  274. [    0.636525@1] ***vcck: vcck_pwm_initregister lm device 0
  275. [    0.641710@1] register lm device 1
  276. [    0.647203@1] usb_wifi_power: on.
  277. [    0.648397@1] chip version=edffb75c
  278. [    0.651879@1] vdac_switch_init_module
  279. [    0.655511@1] tv_init_module
  280. [    0.658261@1] major number 254 for disp
  281. [    0.662169@1] vout_register_server
  282. [    0.665547@1] register tv module server ok
  283. [    0.669894@1] /opt/yuetv_release_c2/src/yuetv_2/common/drivers/amlogic/i2c/aml_i2c.c : aml_i2c_init
  284. [    0.678944@1] HDMI DEBUG: amhdmitx_init [1818]
  285. [    0.683262@1] HDMI Ver: 2013Aug25a
  286. [    0.686658@1] HDMI DEBUG: amhdmitx_probe [1625]
  287. [    0.691501@1] Set HDMI:Chip C
  288. [    0.694111@1] HDMI: get hdmi platform data
  289. [    0.698183@1] HDMI 5V Power On
  290. [    0.701235@1] HDMI DEBUG: HDMITX_M1B_Init [3424]
  291. [    0.705824@1] HDMI DEBUG: HDMITX_M1B_Init [3427]
  292. [    0.710423@1] HDMI DEBUG: hdmi_hw_init [1204]
  293. [    0.714834@1] HDMI: get brd phy data
  294. [    0.718396@1] hdmi phy setting
  295. [    0.721692@1] HDMI: get brd phy data
  296. [    0.724968@1] hdmi phy setting
  297. [    0.729180@1] ------------[ cut here ]------------
  298. [    0.732759@1] WARNING: at /opt/yuetv_release_c2/src/yuetv_2/common/fs/sysfs/dir.c:455 sysfs_add_one+0x88/0xbc()
  299. [    0.742931@1] HDMI: reset intr mask
  300. [    0.746275@1] sysfs: cannot create duplicate filename '/module/hdmitx/version'
  301. [    0.753482@1] Modules linked in:
  302. [    0.756718@1] [<c0043b44>] (unwind_backtrace+0x0/0xf8) from [<c0061ee4>] (warn_slowpath_common+0x4c/0x64)
  303. [    0.766248@1] HDMI DEBUG: hdmi_task_handle [1253]
  304. [    0.766254@0] HDMI irq 1
  305. [    0.766264@0] Reg0x196 = 0x2  Reg0x80 = 0x1  Reg0x26 = 0xc
  306. [    0.766282@0] Reg0x196 = 0x42  Reg0x80 = 0x1  Reg0x26 = 0x4c
  307. [    0.784569@1] [<c0061ee4>] (warn_slowpath_common+0x4c/0x64) from [<c0061f90>] (warn_slowpath_fmt+0x30/0x40)
  308. [    0.794286@1] [<c0061f90>] (warn_slowpath_fmt+0x30/0x40) from [<c0122df4>] (sysfs_add_one+0x88/0xbc)
  309. [    0.803405@1] [<c0122df4>] (sysfs_add_one+0x88/0xbc) from [<c0121f38>] (sysfs_add_file_mode+0x4c/0x9c)
  310. [    0.812693@1] [<c0121f38>] (sysfs_add_file_mode+0x4c/0x9c) from [<c000fa64>] (param_sysfs_init+0x70/0x1b0)
  311. [    0.822331@1] [<c000fa64>] (param_sysfs_init+0x70/0x1b0) from [<c003770c>] (do_one_initcall+0xfc/0x164)
  312. [    0.831694@1] [<c003770c>] (do_one_initcall+0xfc/0x164) from [<c0008988>] (kernel_init+0x98/0x13c)
  313. [    0.840628@1] [<c0008988>] (kernel_init+0x98/0x13c) from [<c003e0c0>] (kernel_thread_exit+0x0/0x8)
  314. [    0.849584@1] ---[ end trace 1b75b31a2719ed1c ]---
  315. [    0.893708@1] bio: create slab <bio-0> at 0
  316. [    0.894572@1] SCSI subsystem initialized
  317. [    0.896405@1] usbcore: registered new interface driver usbfs
  318. [    0.902440@1] usbcore: registered new interface driver hub
  319. [    0.907409@1] usbcore: registered new device driver usb
  320. [    0.912900@1] LCD driver init
  321. [    0.915592@1] [0x1b7e] = 0xff
  322. [    0.918376@1] [0x105f] = 0x0
  323. [    0.921252@1] [0x109d] = 0x814d3928
  324. [    0.924713@1] [0x109e] = 0x6b425012
  325. [    0.928185@1] [0x109f] = 0x110
  326. [    0.931229@1] [0x109c] = 0x1043e
  327. [    0.934434@1] [0x1066] = 0x10843
  328. [    0.937646@1] [0x1059] = 0x100
  329. [    0.940684@1] [0x105f] = 0x80000
  330. [    0.943902@1] [0x105f] = 0x88001
  331. [    0.947107@1] [0x105f] = 0x80003
  332. [    0.950319@1] [0x104a] = 0x101
  333. [    0.953362@1] [0x107f] = 0x8c0000c3
  334. [    0.956829@1] [0x1bb8] = 0x52
  335. [    0.959780@1] [0x1b62] = 0x2029
  336. [    0.962909@1] [0x1b8d] = 0x4040
  337. [    0.966030@1] [0x1b8e] = 0x19
  338. [    0.968981@1] [0x1b94] = 0x288
  339. [    0.972024@1] [0x1b95] = 0xc87
  340. [    0.975057@1] [0x1b97] = 0xce3
  341. [    0.978095@1] [0x1b98] = 0x50
  342. [    0.981046@1] [0x1b99] = 0xf0
  343. [    0.984001@1] [0x1b9a] = 0x50
  344. [    0.986949@1] [0x1b9b] = 0x2b0
  345. [    0.989987@1] [0x1b9c] = 0xcb0
  346. [    0.993028@1] [0x1b9d] = 0x4
  347. [    0.995889@1] [0x1b9e] = 0x8
  348. [    0.998753@1] [0x1ba1] = 0x4
  349. [    1.001621@1] [0x1ba2] = 0x8
  350. [    1.004482@1] [0x1ba4] = 0x288
  351. [    1.007520@1] [0x1ba3] = 0xc87
  352. [    1.010558@1] [0x1ba6] = 0x1d
  353. [    1.013513@1] [0x1baf] = 0x2ec
  354. [    1.016547@1] [0x1ba7] = 0x100
  355. [    1.019585@1] [0x1ba8] = 0xa8
  356. [    1.022548@1] [0x1ba9] = 0xa8
  357. [    1.025488@1] [0x1baa] = 0x100
  358. [    1.028525@1] [0x1bab] = 0x0
  359. [    1.031394@1] [0x1bac] = 0x5
  360. [    1.034254@1] [0x1bae] = 0x2ed
  361. [    1.037292@1] [0x1b68] = 0x100
  362. [    1.040330@1] [0x1b60] = 0x0
  363. [    1.043198@1] [0x1b6e] = 0x200
  364. [    1.046233@1] [0x1b58] = 0x0
  365. [    1.049097@1] [0x1b7e] = 0x0
  366. [    1.051965@1] [0x1b64] = 0x9061
  367. [    1.055087@1] [0x1b65] = 0xa061
  368. [    1.058211@1] [0x1b66] = 0xb061
  369. [    1.061340@1] [0x1b78] = 0x1
  370. [    1.064201@1] [0x1b79] = 0x1
  371. [    1.067065@1] [0x1b7a] = 0x1
  372. [    1.069929@1] [0x1b7b] = 0x1
  373. [    1.072798@1] [0x1b7c] = 0x1
  374. [    1.075658@1] [0x1b7d] = 0x1
  375. [    1.078523@1] [0x271a] = 0xa
  376. [    1.081391@1] [0x1bfc] = 0x1000
  377. [    1.084512@1] [0x1c0d] = 0x3102
  378. [    1.087637@1] [0x1c0e] = 0x54
  379. [    1.090588@1] [0x1b80] = 0x1
  380. [    1.093456@1] [0x1b57] = 0x0
  381. [    1.096318@1] tvoutc_setmode[267]
  382. [    1.099616@1] mode is: 6
  383. [    1.102139@1] VPU_VIU_VENC_MUX_CTRL: 0xa
  384. [    1.106038@1] viu chan = 1
  385. [    1.108729@1] VPU_VIU_VENC_MUX_CTRL: 0xa
  386. [    1.191513@1] request_fiq:152: fiq=35
  387. [    1.191541@1] request_fiq:186: end
  388. [    1.225052@0] print_constraints: vcck: 1010 <--> 1370 mV at 1380 mV
  389. [    1.226229@0] Advanced Linux Sound Architecture Driver Version 1.0.24.
  390. [    1.232962@0] Bluetooth: Core ver 2.16
  391. [    1.236106@0] NET: Registered protocol family 31
  392. [    1.240606@0] Bluetooth: HCI device and connection manager initialized
  393. [    1.247149@0] Bluetooth: HCI socket layer initialized
  394. [    1.252189@0] Bluetooth: L2CAP socket layer initialized
  395. [    1.257376@0] Bluetooth: SCO socket layer initialized
  396. [    1.263447@1] Switching to clocksource Timer-E
  397. [    1.271222@0] Switched to NOHz mode on CPU #0
  398. [    1.271230@1] Switched to NOHz mode on CPU #1
  399. [    1.276883@0] cfg80211: Calling CRDA to update world regulatory domain
  400. [    1.287372@1] NET: Registered protocol family 2
  401. [    1.287514@1] IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
  402. [    1.294040@1] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
  403. [    1.301813@1] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
  404. [    1.308627@1] TCP: Hash tables configured (established 65536 bind 65536)
  405. [    1.314562@1] TCP reno registered
  406. [    1.318211@1] HDMI: EDID Ready
  407. [    1.321006@1] UDP hash table entries: 256 (order: 1, 8192 bytes)
  408. [    1.326961@1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  409. [    1.333339@1] CEC: Physical address: 0x1000
  410. [    1.337491@1] CEC: Physical address: 1.0.0.0
  411. [    1.341771@1] HDMI: get current mode: 720p
  412. [    1.345826@1] set mode VIC 4 (cd0,cs0,pm1,vd0,1)
  413. [    1.347173@0] NET: Registered protocol family 1
  414. [    1.347354@0] Unpacking initramfs...
  415. [    1.358612@1] HDMI DEBUG: hdmi_hw_reset [1377]
  416. [    1.363001@1] HDMI: get brd phy data
  417. [    1.366551@1] hdmi phy setting
  418. [    1.370701@1] HDMI: get brd phy data
  419. [    1.373149@1] hdmi phy setting
  420. [    1.376240@1] HDMI DEBUG: hdmitx_set_pll [2058]
  421. [    1.380730@1] param->VIC:4
  422. [    1.383393@1] mode is: 6
  423. [    1.385912@1] VPU_VIU_VENC_MUX_CTRL: 0xa
  424. [    1.389837@1] viu chan = 1
  425. [    1.392505@1] VPU_VIU_VENC_MUX_CTRL: 0xa
  426. [    1.402734@0] Freeing initrd memory: 1068K
  427. [    1.403988@0] highmem bounce pool size: 64 pages
  428. [    1.406035@0] ashmem: initialized
  429. [    1.419980@1] Sink is HDMI device
  430. [    1.420022@1] Source in HDMI Mode
  431. [    1.421156@1] CEC not ready
  432. [    1.424027@0] NTFS driver 2.1.30 [Flags: R/O].
  433. [    1.428566@0] fuse init (API version 7.16)
  434. [    1.432866@0] msgmni has been set to 570
  435. [    1.437033@0] io scheduler noop registered
  436. [    1.440221@0] io scheduler deadline registered (default)
  437. [    1.526931@1] HDMI: audio channel num is 0
  438. [    1.526989@1] current VIC: 4
  439. [    1.528251@1] audio sample rate: 0
  440. [    1.531636@1] HDMI: reset audio N para
  441. [    1.535374@1] PCM out to HDMI
  442. [    1.561698@1] Time out: AIU_HDMI_CLK_DATA_CTRL
  443. [    1.561742@1] i2s_to_spdif_flag:1
  444. [    1.563891@1] Enable audio spdif to HDMI
  445. [    1.567882@1] HDMI: set audio param
  446. [    1.624675@0] loop: module loaded
  447. [    1.626919@0] PPP generic driver version 2.4.2
  448. [    1.627436@0] PPP Deflate Compression module registered
  449. [    1.631987@0] PPP BSD Compression module registered
  450. [    1.637250@0] PPP MPPE Compression module registered
  451. [    1.641797@0] NET: Registered protocol family 24
  452. [    1.646400@0] tun: Universal TUN/TAP device driver, 1.6
  453. [    1.651656@0] tun: (C) 1999-2004 Max Krasnyansky <[email]maxk@qualcomm.com[/email]>
  454. [    1.658811@0] usbcore: registered new interface driver cdc_acm
  455. [    1.663756@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  456. [    1.671945@0] Initializing USB Mass Storage driver...
  457. [    1.677095@0] usbcore: registered new interface driver usb-storage
  458. [    1.683111@0] USB Mass Storage support registered.
  459. [    1.688121@0] usbcore: registered new interface driver usbserial
  460. [    1.693875@0] usbserial: USB Serial Driver core
  461. [    1.698500@0] USB Serial support registered for GSM modem (1-port)
  462. [    1.704646@0] usbcore: registered new interface driver option
  463. [    1.710295@0] option: v0.7.2:USB Driver for GSM modems
  464. [    1.716167@0] mousedev: PS/2 mouse device common for all mice
  465. [    1.722398@0] usbcore: registered new interface driver iforce
  466. [    1.728046@0] usbcore: registered new interface driver xpad
  467. [    1.732611@0] usbcore: registered new interface driver usb_nanosic_ts
  468. [    1.739765@0] i2c /dev entries driver
  469. [    1.742800@0] lirc_dev: IR Remote Control driver registered, major 250
  470. [    1.749109@0] IR NEC protocol handler initialized
  471. [    1.753767@0] IR RC5(x) protocol handler initialized
  472. [    1.758724@0] IR RC6 protocol handler initialized
  473. [    1.763402@0] IR JVC protocol handler initialized
  474. [    1.768098@0] IR Sony protocol handler initialized
  475. [    1.772863@0] IR RC5 (streamzap) protocol handler initialized
  476. [    1.778601@0] IR LIRC bridge handler initialized
  477. [    1.783192@0] Linux video capture interface: v2.00
  478. [    1.788210@0] usbcore: registered new interface driver uvcvideo
  479. [    1.793869@0] USB Video Class driver (v1.1.0)
  480. [    1.799024@0] device-mapper: uevent: version 1.0.3
  481. [    1.803653@0] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: [email]dm-devel@redhat.com[/email]
  482. [    1.811849@0] Bluetooth: HCI UART driver ver 2.2
  483. [    1.816180@0] Bluetooth: HCI H4 protocol initialized
  484. [    1.821173@0] cpuidle: using governor ladder
  485. [    1.825378@0] cpuidle: using governor menu
  486. [    1.830598@0] usbcore: registered new interface driver usbhid
  487. [    1.835186@0] usbhid: USB HID core driver
  488. [    1.839965@0] logger: created 256K log 'log_main'
  489. [    1.844128@0] logger: created 256K log 'log_events'
  490. [    1.849002@0] logger: created 256K log 'log_radio'
  491. [    1.853749@0] logger: created 256K log 'log_system'
  492. [    1.858490@0] vout_init_module
  493. [    1.861438@0] start init vout module
  494. [    1.865229@0] create  vout attribute ok
  495. [    1.869246@0] ge2d_init
  496. [    1.871561@0] ge2d_dev major:248
  497. [    1.875324@0] ge2d start monitor
  498. [    1.878210@0] osd_init
  499. [    1.878215@1] ge2d workqueue monitor start
  500. [    1.884702@0] [osd0] 0x84100000-0x850fffff
  501. [    1.888983@0] Frame buffer memory assigned at phy:0x84100000, vir:0xe1000000, size=16384K
  502. [    1.896914@0] ---------------clear framebuffer0 memory
  503. [    1.914859@0] [osd1] 0x85100000-0x851fffff
  504. [    1.914911@0] Frame buffer memory assigned at phy:0x85100000, vir:0xe0200000, size=1024K
  505. [    1.921401@0] init fbdev bpp is :24
  506. [    1.926063@0] osd probe ok
  507. [    1.934536@0] amlvideo-000: V4L2 device registered as video10
  508. [    1.935327@0]  set pinmux c08753d8
  509. [    1.938073@0]  set pinmux c08753e0
  510. [    1.966893@0] UART_ttyS0:(irq = 122)
  511. [    1.996888@0] UART_ttyS1:(irq = 58)
  512. [    1.997045@0] dwc_otg: version 2.94a 05-DEC-2012
  513. [    2.499228@0] USB (0) use clock source: XTAL input
  514. [    2.566864@1] HDMITX: no HDCP key available
  515. [    2.566888@1] HDMITX: HDCP Key error
  516. [    2.568964@1] HDMITX: no HDCP key available
  517. [    2.573125@1] HDMITX: HDCP Key error
  518. [    2.900179@0] Core Release: 2.94a
  519. [    2.900202@0] Setting default values for core params
  520. [    3.302808@0] Using Buffer DMA mode
  521. [    3.302831@0] OTG VER PARAM: 1, OTG VER FLAG: 1
  522. [    3.305163@0] Working on port type = HOST
  523. [    3.309241@0] dwc_otg lm0: DWC OTG Controller
  524. [    3.313580@0] dwc_otg lm0: new USB bus registered, assigned bus number 1
  525. [    3.320239@0] dwc_otg lm0: irq 62, io mem 0x00000000
  526. [    3.328249@0] Init: Port Power? op_state=1
  527. [    3.329207@0] Init: Power Port (0)
  528. [    3.333440@0] hub 1-0:1.0: USB hub found
  529. [    3.336510@0] hub 1-0:1.0: 1 port detected
  530. [    3.740932@0] Core Release: 2.94a
  531. [    3.740954@0] Setting default values for core params
  532. [    4.143569@0] Using Buffer DMA mode
  533. [    4.143592@0] OTG VER PARAM: 1, OTG VER FLAG: 1
  534. [    4.145927@0] Working on port type = HOST
  535. [    4.149993@0] dwc_otg lm1: DWC OTG Controller
  536. [    4.154292@0] dwc_otg lm1: new USB bus registered, assigned bus number 2
  537. [    4.160994@0] dwc_otg lm1: irq 63, io mem 0x00000000
  538. [    4.168975@0] Init: Port Power? op_state=1
  539. [    4.169970@0] Init: Power Port (0)
  540. [    4.174169@0] hub 2-0:1.0: USB hub found
  541. [    4.177315@0] hub 2-0:1.0: 1 port detected
  542. [    4.181733@0] Amlogic nand flash Kernel driver, Version K1.06.015 (c) 2010 Amlogic Inc.
  543. [    4.189363@0] ####Version of Uboot must be newer than U1.06.011!!!!!
  544. [    4.195795@0] 2
  545. [    4.197521@0] SPI BOOT, m3_nand_probe continue i 0
  546. [    4.202263@0] chip->controller=c09ed01c
  547. [    4.206079@0] checking ChiprevD :0
  548. [    4.209492@0] aml_nand_probe checked chiprev:0
  549. [    4.213904@0] init bus_cycle=17, bus_timing=10, start_cycle=10, end_cycle=10,system=5.0ns
  550. [    4.222505@0] No NAND device found.
  551. [    4.225763@0] NAND device id: 98 d7 84 93 72 57
  552. [    4.230158@0] NAND device: Manufacturer ID: 0x98, Chip ID: 0x98 (Toshiba A serials NAND 4GiB TC58TEG5DCJTA00 )
  553. [    4.240248@0] #####aml_nand_init, with RB pins and chip->chip_delay:20
  554. [    4.246620@0] bus_cycle=5, bus_timing=7, start_cycle=6, end_cycle=9,system=5.0ns
  555. [    4.254020@0] oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH40_1K_MODE
  556. [    4.264518@0] aml_chip->oob_fill_cnt =128,aml_chip->oob_size =1280,bch_bytes =70
  557. [    4.271896@0] multi plane error for selected plane mode: NAND_TWO_PLANE_MODE force plane to : NAND_SINGLE_PLANE_MODE
  558. [    4.282421@0]  oob layout use nand base oob layout oobsize = 32,oobmul =1,mtd->oobsize =1280,aml_chip->oob_size =1280
  559. [    4.300444@0] aml nand env valid addr: 8000
  560. [    4.317160@0] nand env: nand_env_probe.
  561. [    4.317867@0] nand key: nand_key_probe.
  562. [    4.319359@0] key start_blk=1016,end_blk=1023,aml_nand_key_init:651
  563. [    4.331532@0] aml nand key valid addr: fe000000
  564. [    4.331557@0] aml nand key valid addr: fe400000
  565. [    4.335107@0] aml nand key valid addr: fe800000
  566. [    4.339735@0] aml nand key valid addr: fec00000
  567. [    4.344359@0] i=0,register --- nand_key NAND bbt detect factory Bad block at 7b000000
  568. [    4.353523@0]  NAND bbt detect factory Bad block at 8b800000
  569. [    4.357969@0] Creating 12 MTD partitions on "A serials NAND 4GiB TC58TEG5DCJTA00 ":
  570. [    4.365579@0] 0x000000800000-0x000001000000 : "bootargs"
  571. [    4.374934@0] 0x000001000000-0x000001800000 : "misc"
  572. [    4.376975@1] Indeed it is in host mode hprt0 = 00021501
  573. [    4.384033@0] 0x000001800000-0x000002000000 : "baseparam"
  574. [    4.387842@0] 0x000002000000-0x000002800000 : "logo"
  575. [    4.392644@0] 0x000002800000-0x000003800000 : "aml_logo"
  576. [    4.398035@0] 0x000003800000-0x000009800000 : "fastplay"
  577. [    4.403250@0] 0x000009800000-0x00000a800000 : "recovery"
  578. [    4.408672@0] 0x00000a800000-0x00000b800000 : "boot"
  579. [    4.413521@0] 0x00000b800000-0x00002b800000 : "system"
  580. [    4.418820@0] 0x00002b800000-0x00004b800000 : "cache"
  581. [    4.423681@0] 0x00004b800000-0x00008c000000 : "userdata"
  582. [    4.427869@0]  NAND bbt detect factory Bad block at 7b000000
  583. [    4.433454@0]  NAND bbt detect factory Bad block at 8b800000
  584. [    4.440480@0] 0x00008c000000-0x0000fe000000 : "NFTL_Part"
  585. [    4.444591@0]  NAND bbt detect factory Bad block at a0000000
  586. [    4.450488@0]  NAND bbt detect factory Bad block at a0800000
  587. [    4.456018@0]  NAND bbt detect factory Bad block at a1800000
  588. [    4.461798@0]  NAND bbt detect factory Bad block at d2000000
  589. [    4.467507@0]  NAND bbt detect factory Bad block at ef400000
  590. [    4.474594@0] init_aml_nftl start
  591. [    4.476512@0] mtd->name: system
  592. [    4.479721@0] nftl version 131218a
  593. [    4.483023@0] nftl part attr 0
  594. [    4.486068@0] nftl start:128,16
  595. [    4.489532@0] first
  596. [    4.528891@0] second 128,112
  597. [    4.556926@1] usb 2-1: new high speed USB device number 2 using dwc_otg
  598. [    4.558193@1] Indeed it is in host mode hprt0 = 00001101
  599. [    4.614591@0] current used block :85
  600. [    4.627028@0] free block cnt = 46
  601. [    4.627047@0] nftl ok!
  602. [    4.627565@0] aml_nftl_blk->mbd.tr.name =system
  603. [    4.632349@1] aml_nftl_init_bounce_buf, use cache here
  604. [    4.637449@0]  system: unknown partition table
  605. [    4.641421@0] _nftl_init_bounce_buf already init 1000
  606. [    4.646135@0] aml_nftl_add_mtd ok
  607. [    4.649486@0] mtd->name: cache
  608. [    4.652477@0] nftl version 131218a
  609. [    4.655869@0] nftl part attr 0
  610. [    4.658951@0] nftl start:128,16
  611. [    4.662339@0] first
  612. [    4.703008@0] second 95,112
  613. [    4.759796@1] hub 2-1:1.0: USB hub found
  614. [    4.760147@1] hub 2-1:1.0: 4 ports detected
  615. [    4.766960@0] current used block :33
  616. [    4.864810@0] free block cnt = 64
  617. [    4.864829@0] nftl ok!
  618. [    4.865334@0] aml_nftl_blk->mbd.tr.name =cache
  619. [    4.870239@1] aml_nftl_init_bounce_buf, use cache here
  620. [    4.875116@0]  cache: unknown partition table
  621. [    4.879113@0] _nftl_init_bounce_buf already init 1000
  622. [    4.883760@0] aml_nftl_add_mtd ok
  623. [    4.887102@0] mtd->name: userdata
  624. [    4.890351@0] nftl version 131218a
  625. [    4.893757@0] nftl part attr 0
  626. [    4.896793@0]  NAND bbt detect factory Bad block at 7b000000
  627. [    4.902537@0]  NAND bbt detect factory Bad block at 8b800000
  628. [    4.908255@0] size_in_blk 258; total_block 256;
  629. [    4.912824@0] nftl start:256,32
  630. [    4.916498@0] first
  631. [    4.981567@0]  NAND bbt detect factory Bad block at 7b000000
  632. [    5.001254@0]  NAND bbt detect factory Bad block at 8b800000
  633. [    5.001653@0] second 55,224
  634. [    5.040944@0] current used block :202
  635. [    5.093566@0] free block cnt = 203
  636. [    5.093585@0] nftl ok!
  637. [    5.094546@0] aml_nftl_blk->mbd.tr.name =data
  638. [    5.098811@1] aml_nftl_init_bounce_buf, use cache here
  639. [    5.103878@0]  data: unknown partition table
  640. [    5.107788@0] _nftl_init_bounce_buf already init 1000
  641. [    5.112421@0] aml_nftl_add_mtd ok
  642. [    5.115720@0] mtd->name: NFTL_Part
  643. [    5.119151@0] nftl version 131218a
  644. [    5.122530@0] nftl part attr 0
  645. [    5.125543@0]  NAND bbt detect factory Bad block at a0000000
  646. [    5.131289@0]  NAND bbt detect factory Bad block at a0800000
  647. [    5.137027@0]  NAND bbt detect factory Bad block at a1800000
  648. [    5.142750@0]  NAND bbt detect factory Bad block at d2000000
  649. [    5.148482@0]  NAND bbt detect factory Bad block at ef400000
  650. [    5.154180@0] size_in_blk 456; total_block 451;
  651. [    5.158797@0] nftl start:451,56
  652. [    5.163041@0] first
  653. [    5.190717@0]  NAND bbt detect factory Bad block at a0000000
  654. [    5.191163@0]  NAND bbt detect factory Bad block at a0800000
  655. [    5.197557@0]  NAND bbt detect factory Bad block at a1800000
  656. [    5.266636@0]  NAND bbt detect factory Bad block at d2000000
  657. [    5.305437@0]  NAND bbt detect factory Bad block at ef400000
  658. [    5.324903@0] second 0,395
  659. [    5.324924@0] all block full!!
  660. [    5.325006@0] free block cnt = 451
  661. [    5.328417@0] nftl ok!
  662. [    5.331702@0] aml_nftl_blk->mbd.tr.name =media
  663. [    5.335911@1] aml_nftl_init_bounce_buf, use cache here
  664. [    5.340389@0]  media: unknown partition table
  665. [    5.344923@0] _nftl_init_bounce_buf already init 1000
  666. [    5.349696@0] aml_nftl_add_mtd ok
  667. [    5.352956@0] init_aml_nftl end
  668. [    5.356081@0] ethernetinit(dbg[c086b338]=1)
  669. [    5.360302@0] ethernet base addr is f3610000
  670. [    5.364498@0] set_phy_mode() phy_Identifier: 0x0
  671. [    5.369263@0] ethernet: MII PHY 0007c0f1h found at address 1, status 0x7809 advertising 01e1.
  672. [    5.377712@0] find phy phy_Identifier=7c0f1
  673. [    5.381770@0] write mac add to:df9a6748: c8 0e 77 02 5b db |..w.[.|
  674. [    5.388460@0] eth0: mixed no checksumming and other settings.
  675. [    5.394215@0] Amlogic A/V streaming port init
  676. [    5.401988@0] regist mpeg12 codec profile
  677. [    5.402177@0] regist mpeg4 codec profile
  678. [    5.405989@0] amvdec_vc1 module init
  679. [    5.409720@0] regist vc1 codec profile
  680. [    5.413280@0] amvdec_h264 module init
  681. [    5.417082@0] regist h264 codec profile
  682. [    5.420744@0] amvdec_h264mvc module init
  683. [    5.424847@0] regist mjpeg codec profile
  684. [    5.428590@0] amvdec_real module init
  685. [    5.432306@0] regist real codec profile
  686. [    5.437177@0] Vsync pts inc(before): 1500
  687. [    5.440016@0] Vsync pts inc(after): 1500
  688. [    5.443921@0] request_fiq:152: fiq=35
  689. [    5.447607@0] request_fiq:186: end
  690. [    5.451640@0] Remote Driver
  691. [    5.454142@0] input: aml_keypad as /devices/platform/meson-remote/input/input0
  692. [    5.461706@0] meson_remote_pinmux_setup()
  693. [    5.464928@0] Remote platform_data g_remote_base=f3100480
  694. [    5.470356@0] Remote date_valye======0,status == 8915d20
  695. [    5.475632@0] remote config major:244
  696. [    5.479861@0] physical address:0x9f950000
  697. [    5.483429@0] Meson KeyInput init
  698. [    5.486685@0] Key 117 registed.
  699. [    5.489800@0] Key 116 registed.
  700. [    5.493091@0] input: key_input as /devices/platform/meson-keyinput.0/input/input1
  701. [    5.500779@0] Meson KeyInput register RTC interrupt
  702. [    5.505054@0] Meson KeyInput major=243
  703. [    5.509993@0]  spi_nor_probe 586
  704. [    5.512147@0] SPI BOOT  : spi_nor_probe 591
  705. [    5.516419@0] spi_nor apollospi:0: mx25l3205d (4096 Kbytes)
  706. [    5.522003@0] Creating 2 MTD partitions on "apollospi:0":
  707. [    5.527369@0] 0x000000000000-0x000000400000 : "bootloader"
  708. [    5.534241@0] 0x000000080000-0x000000088000 : "ubootenv"
  709. [    5.540010@0] Memory Card media Major: 253
  710. [    5.542325@0] card max_req_size is 128K
  711. [    5.546793@0] card creat process sucessful
  712. [    5.550265@0]
  713. [    5.550269@0] SD/MMC initialization started......
  714. [    6.186866@0] mmc data3 pull high
  715. [    6.187090@0] sd_mmc_info->card_type=0
  716. [    6.188274@0] begin SDIO check ......
  717. [    6.214491@0] sdio_timeout_int_times = 0; timeout = 498
  718. [    6.237087@0] sdio_timeout_int_times = 0; timeout = 497
  719. [    6.237114@0] SEND OP timeout @1
  720. [    6.239877@0] mmc data3 pull high
  721. [    6.243366@0] begin SD&SDHC check ......
  722. [    6.289431@0] sdio_timeout_int_times = 0; timeout = 498
  723. [    6.289458@0] SEND IF timeout @2
  724. [    6.314984@0] sdio_timeout_int_times = 0; timeout = 498
  725. [    6.315011@0] begin MMC check ......
  726. [    6.359427@0] sdio_timeout_int_times = 0; timeout = 498
  727. [    6.359456@0] No any SD/MMC card detected!
  728. [    6.363092@0] #SD_MMC_ERROR_DRIVER_FAILURE error occured in sd_voltage_validation()
  729. [    6.370761@0] [card_force_init] unit_state 3
  730. [    6.375141@0] [dsp]DSP start addr 0xc4000000
  731. [    6.379304@0] [dsp]register dsp to char divece(232)
  732. [    6.389259@0] DSP pcmenc stream buffer to [0x9e401000-0x9e601000]
  733. [    6.390175@0] amlogic audio dsp pcmenc device init!
  734. [    6.395923@0] amlogic audio spdif interface device init!
  735. [    6.401619@0] using rtc device, aml_rtc, for alarms
  736. [    6.405047@0] aml_rtc aml_rtc: rtc core: registered aml_rtc as rtc0
  737. [    6.412367@0] efuse===========================================
  738. [    6.417942@0] efuse: device efuse created
  739. [    6.421359@0] efuse--------------------------------------------
  740. [    6.427255@0] keys===========================================
  741. [    6.432882@0] keys_devno=ee00000
  742. [    6.436612@0] efuse: device aml_keys created
  743. [    6.440398@0] amlkeys=0
  744. [    6.442878@0] platform_driver_register--aml_keys_driver--------------------
  745. [    6.466876@0] 6amlogic audio data interface device init!
  746. [    6.467560@0] amlogic rfkill init
  747. [    6.497046@0] BT_RADIO going: on
  748. [    6.497067@0] BCM_BT: going ON
  749. [    6.557063@0] aml_hw_crypto initialization.
  750. [    6.558023@0] usbcore: registered new interface driver snd-usb-audio
  751. [    6.562876@0] enter dummy_codec_audio_probe
  752. [    6.566304@0] sound card index = #0
  753. [    6.569468@0] sound card index = #(null)
  754. [    6.573661@0] aml-pcm 0:playback preallocate_dma_buffer: area=ffdf0000, addr=9f0f8000, size=16384
  755. [    6.582768@0] iec958 0: preallocate dma buffer start=ffde0000, size=10000
  756. [    6.589783@0] aml-pcm 1:capture preallocate_dma_buffer: area=ffda0000, addr=9f340000, size=65536
  757. [    6.597917@0] asoc: dummy_codec <-> aml-dai0 mapping ok
  758. [    6.604552@0] ALSA device list:
  759. [    6.606211@0]   #0: AML-DUMMY-CODEC
  760. [    6.609897@0] GACT probability NOT on
  761. [    6.613336@0] Mirror/redirect action on
  762. [    6.617192@0] u32 classifier
  763. [    6.620011@0]     Actions configured
  764. [    6.623572@0] Netfilter messages via NETLINK v0.30.
  765. [    6.628509@0] nf_conntrack version 0.5.0 (12752 buckets, 51008 max)
  766. [    6.635431@0] ctnetlink v0.93: registering with nfnetlink.
  767. [    6.640238@0] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
  768. [    6.647300@0] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
  769. [    6.653985@0] xt_time: kernel timezone is -0000
  770. [    6.657994@0] ip_tables: (C) 2000-2006 Netfilter Core Team
  771. [    6.663382@0] arp_tables: (C) 2002 David S. Miller
  772. [    6.668117@0] TCP cubic registered
  773. [    6.672554@0] NET: Registered protocol family 10
  774. [    6.676817@0] Mobile IPv6
  775. [    6.678717@0] ip6_tables: (C) 2000-2006 Netfilter Core Team
  776. [    6.684281@0] IPv6 over IPv4 tunneling driver
  777. [    6.689828@0] NET: Registered protocol family 17
  778. [    6.693136@0] NET: Registered protocol family 15
  779. [    6.697897@0] Bridge firewalling registered
  780. [    6.701983@0] Bluetooth: RFCOMM TTY layer initialized
  781. [    6.706958@0] Bluetooth: RFCOMM socket layer initialized
  782. [    6.712195@0] Bluetooth: RFCOMM ver 1.11
  783. [    6.716101@0] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
  784. [    6.721601@0] Bluetooth: BNEP filters: protocol multicast
  785. [    6.726989@0] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  786. [    6.733231@0] NET: Registered protocol family 35
  787. [    6.737990@0] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
  788. [    6.745447@0] DDR low power is enable.
  789. [    6.749248@0] enter meson_pm_probe!
  790. [    6.752647@0] meson_pm_probe done !
  791. [    6.756601@0] ------------[ cut here ]------------
  792. [    6.760907@0] WARNING: at /opt/yuetv_release_c2/src/yuetv_2/common/kernel/smp.c:459 smp_call_function_many+0xc8/0x280()
  793. [    6.771647@0] Modules linked in:
  794. [    6.774884@0] [<c0043b44>] (unwind_backtrace+0x0/0xf8) from [<c0061ee4>] (warn_slowpath_common+0x4c/0x64)
  795. [    6.784415@0] [<c0061ee4>] (warn_slowpath_common+0x4c/0x64) from [<c0061f18>] (warn_slowpath_null+0x1c/0x24)
  796. [    6.794222@0] [<c0061f18>] (warn_slowpath_null+0x1c/0x24) from [<c008f598>] (smp_call_function_many+0xc8/0x280)
  797. [    6.804292@0] [<c008f598>] (smp_call_function_many+0xc8/0x280) from [<c008f784>] (smp_call_function+0x34/0x68)
  798. [    6.814276@0] [<c008f784>] (smp_call_function+0x34/0x68) from [<c0049c2c>] (clk_set_rate_a9+0x9c/0xdc)
  799. [    6.823560@0] [<c0049c2c>] (clk_set_rate_a9+0x9c/0xdc) from [<c0049f28>] (meson_clk_set_rate+0x130/0x168)
  800. [    6.833108@0] [<c0049f28>] (meson_clk_set_rate+0x130/0x168) from [<c0049ff4>] (clk_set_rate+0x94/0xbc)
  801. [    6.842397@0] [<c0049ff4>] (clk_set_rate+0x94/0xbc) from [<c0052d28>] (meson_cpufreq_target_locked.isra.2+0x14c/0x224)
  802. [    6.853072@0] [<c0052d28>] (meson_cpufreq_target_locked.isra.2+0x14c/0x224) from [<c0052e24>] (meson_cpufreq_target+0x24/0x3c)
  803. [    6.864445@0] [<c0052e24>] (meson_cpufreq_target+0x24/0x3c) from [<c0370570>] (__cpufreq_driver_target+0x50/0x64)
  804. [    6.874688@0] [<c0370570>] (__cpufreq_driver_target+0x50/0x64) from [<c0372d1c>] (cpufreq_governor_performance+0x28/0x30)
  805. [    6.885622@0] [<c0372d1c>] (cpufreq_governor_performance+0x28/0x30) from [<c0370658>] (__cpufreq_governor+0xb0/0x138)
  806. [    6.896211@0] [<c0370658>] (__cpufreq_governor+0xb0/0x138) from [<c03714b8>] (__cpufreq_set_policy+0x128/0x168)
  807. [    6.906280@0] [<c03714b8>] (__cpufreq_set_policy+0x128/0x168) from [<c0371758>] (cpufreq_add_dev_interface+0x260/0x2c8)
  808. [    6.917043@0] [<c0371758>] (cpufreq_add_dev_interface+0x260/0x2c8) from [<c0371c7c>] (cpufreq_add_dev+0x4bc/0x634)
  809. [    6.927375@0] [<c0371c7c>] (cpufreq_add_dev+0x4bc/0x634) from [<c029aa98>] (sysdev_driver_register+0xb0/0x12c)
  810. [    6.937356@0] [<c029aa98>] (sysdev_driver_register+0xb0/0x12c) from [<c0370b24>] (cpufreq_register_driver+0x70/0x17c)
  811. [    6.947947@0] [<c0370b24>] (cpufreq_register_driver+0x70/0x17c) from [<c029d318>] (platform_drv_probe+0x18/0x1c)
  812. [    6.958101@0] [<c029d318>] (platform_drv_probe+0x18/0x1c) from [<c029c10c>] (driver_probe_device+0x90/0x1ac)
  813. [    6.967908@0] [<c029c10c>] (driver_probe_device+0x90/0x1ac) from [<c029c2b4>] (__driver_attach+0x8c/0x90)
  814. [    6.977456@0] [<c029c2b4>] (__driver_attach+0x8c/0x90) from [<c029b32c>] (bus_for_each_dev+0x5c/0x88)
  815. [    6.986656@0] [<c029b32c>] (bus_for_each_dev+0x5c/0x88) from [<c029baf0>] (bus_add_driver+0x17c/0x244)
  816. [    6.995944@0] [<c029baf0>] (bus_add_driver+0x17c/0x244) from [<c029c760>] (driver_register+0x78/0x13c)
  817. [    7.005232@0] [<c029c760>] (driver_register+0x78/0x13c) from [<c029d6c8>] (platform_driver_probe+0x18/0x9c)
  818. [    7.014959@0] [<c029d6c8>] (platform_driver_probe+0x18/0x9c) from [<c003770c>] (do_one_initcall+0xfc/0x164)
  819. [    7.024679@0] [<c003770c>] (do_one_initcall+0xfc/0x164) from [<c0008988>] (kernel_init+0x98/0x13c)
  820. [    7.033617@0] [<c0008988>] (kernel_init+0x98/0x13c) from [<c003e0c0>] (kernel_thread_exit+0x0/0x8)
  821. [    7.042554@0] ---[ end trace 1b75b31a2719ed1d ]---
  822. [    7.047327@0] ------------[ cut here ]------------
  823. [    7.052103@0] WARNING: at /opt/yuetv_release_c2/src/yuetv_2/common/kernel/smp.c:320 smp_call_function_single+0x150/0x1c0()
  824. [    7.063122@0] Modules linked in:
  825. [    7.066342@0] [<c0043b44>] (unwind_backtrace+0x0/0xf8) from [<c0061ee4>] (warn_slowpath_common+0x4c/0x64)
  826. [    7.075887@0] [<c0061ee4>] (warn_slowpath_common+0x4c/0x64) from [<c0061f18>] (warn_slowpath_null+0x1c/0x24)
  827. [    7.085696@0] [<c0061f18>] (warn_slowpath_null+0x1c/0x24) from [<c008f460>] (smp_call_function_single+0x150/0x1c0)
  828. [    7.096026@0] [<c008f460>] (smp_call_function_single+0x150/0x1c0) from [<c008f784>] (smp_call_function+0x34/0x68)
  829. [    7.106268@0] [<c008f784>] (smp_call_function+0x34/0x68) from [<c0049c2c>] (clk_set_rate_a9+0x9c/0xdc)
  830. [    7.115555@0] [<c0049c2c>] (clk_set_rate_a9+0x9c/0xdc) from [<c0049f28>] (meson_clk_set_rate+0x130/0x168)
  831. [    7.125103@0] [<c0049f28>] (meson_clk_set_rate+0x130/0x168) from [<c0049ff4>] (clk_set_rate+0x94/0xbc)
  832. [    7.134391@0] [<c0049ff4>] (clk_set_rate+0x94/0xbc) from [<c0052d28>] (meson_cpufreq_target_locked.isra.2+0x14c/0x224)
  833. [    7.145067@0] [<c0052d28>] (meson_cpufreq_target_locked.isra.2+0x14c/0x224) from [<c0052e24>] (meson_cpufreq_target+0x24/0x3c)
  834. [    7.156438@0] [<c0052e24>] (meson_cpufreq_target+0x24/0x3c) from [<c0370570>] (__cpufreq_driver_target+0x50/0x64)
  835. [    7.166682@0] [<c0370570>] (__cpufreq_driver_target+0x50/0x64) from [<c0372d1c>] (cpufreq_governor_performance+0x28/0x30)
  836. [    7.177618@0] [<c0372d1c>] (cpufreq_governor_performance+0x28/0x30) from [<c0370658>] (__cpufreq_governor+0xb0/0x138)
  837. [    7.188207@0] [<c0370658>] (__cpufreq_governor+0xb0/0x138) from [<c03714b8>] (__cpufreq_set_policy+0x128/0x168)
  838. [    7.198276@0] [<c03714b8>] (__cpufreq_set_policy+0x128/0x168) from [<c0371758>] (cpufreq_add_dev_interface+0x260/0x2c8)
  839. [    7.209039@0] [<c0371758>] (cpufreq_add_dev_interface+0x260/0x2c8) from [<c0371c7c>] (cpufreq_add_dev+0x4bc/0x634)
  840. [    7.219368@0] [<c0371c7c>] (cpufreq_add_dev+0x4bc/0x634) from [<c029aa98>] (sysdev_driver_register+0xb0/0x12c)
  841. [    7.229350@0] [<c029aa98>] (sysdev_driver_register+0xb0/0x12c) from [<c0370b24>] (cpufreq_register_driver+0x70/0x17c)
  842. [    7.239941@0] [<c0370b24>] (cpufreq_register_driver+0x70/0x17c) from [<c029d318>] (platform_drv_probe+0x18/0x1c)
  843. [    7.250096@0] [<c029d318>] (platform_drv_probe+0x18/0x1c) from [<c029c10c>] (driver_probe_device+0x90/0x1ac)
  844. [    7.259904@0] [<c029c10c>] (driver_probe_device+0x90/0x1ac) from [<c029c2b4>] (__driver_attach+0x8c/0x90)
  845. [    7.269452@0] [<c029c2b4>] (__driver_attach+0x8c/0x90) from [<c029b32c>] (bus_for_each_dev+0x5c/0x88)
  846. [    7.278653@0] [<c029b32c>] (bus_for_each_dev+0x5c/0x88) from [<c029baf0>] (bus_add_driver+0x17c/0x244)
  847. [    7.287940@0] [<c029baf0>] (bus_add_driver+0x17c/0x244) from [<c029c760>] (driver_register+0x78/0x13c)
  848. [    7.297228@0] [<c029c760>] (driver_register+0x78/0x13c) from [<c029d6c8>] (platform_driver_probe+0x18/0x9c)
  849. [    7.306950@0] [<c029d6c8>] (platform_driver_probe+0x18/0x9c) from [<c003770c>] (do_one_initcall+0xfc/0x164)
  850. [    7.316671@0] [<c003770c>] (do_one_initcall+0xfc/0x164) from [<c0008988>] (kernel_init+0x98/0x13c)
  851. [    7.325611@0] [<c0008988>] (kernel_init+0x98/0x13c) from [<c003e0c0>] (kernel_thread_exit+0x0/0x8)
  852. [    7.334548@0] ---[ end trace 1b75b31a2719ed1e ]---
  853. [    7.342779@0] ERROR::usb_gadget_probe_driver:1316: usb_gadget_register_driver ENODEV
  854. [    7.342784@0]
  855. [    7.349288@0] aml_rtc aml_rtc: setting system clock to 1970-01-01 00:00:12 UTC (12)
  856. [    7.356342@0] CEC init
  857. [    7.358776@1] CEC: CEC task process
  858. [    7.362216@0] i[    7.386878@0] Changing baud from 0 to 115200
  859. [    7.446933@0] Freeing init memory: 188K
  860. [    7.450392@1] init: /init.amlogic.rc: 373: ignored duplicate definition of service 'smbd'
  861. [    7.453900@1] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
  862. [    7.462543@1] init: try mount debugfs to target /sys/kernel/debug
  863. [    7.468302@1] init: try mount none to target /proc/bus/usb
  864. [    7.480523@1] UMP: UMP device driver  loaded
  865. [    7.504792@1] Mali pp1 MMU register mapped at e001e000...
  866. [    7.504848@1] Mali pp2 MMU register mapped at e00cc000...
  867. [    7.509973@1] mali_meson_poweron: Mali APB bus accessing
  868. [    7.515226@1] ..........accessing done.
  869. [    7.582058@1] mali_meson_poweron: Interrupt received.
  870. [    7.648808@1] Mali: Mali device driver loaded
  871. [    8.650017@1] init: try mount none to target /acct
  872. [    8.687267@0] init: try mount tmpfs to target /mnt/secure
  873. [    8.687477@0] init: try mount tmpfs to target /mnt/asec
  874. [    8.692340@0] init: try mount tmpfs to target /mnt/obb
  875. [    8.698023@0] init: try mount none to target /dev/cpuctl
  876. [    8.737791@1] init: try mount tmpfs to target /storage/external_storage
  877. [    8.739037@1] init: try mount /dev/block/system to target /system
  878. [    8.753480@0] EXT4-fs (system): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
  879. [    8.757158@0] yaffs: dev is 32505861 name is "mtdblock5" rw
  880. [    8.762188@0] yaffs: passed flags ""
  881. [    8.798804@0] init: try mount /dev/block/fastplay to target /fastplay
  882. [    8.799789@0] vfm_map_store:rm default
  883. [    8.803385@0] vfm_map_store:add default decoder ppmgr deinterlace amvideo
  884. [    8.819104@0] init: Before e2fsck_main...
  885. [    9.061382@0] init: After e2fsck_main...
  886. [    9.061450@0] init: Before e2fsck_main...
  887. [    9.063982@0] init: After e2fsck_main...
  888. [    9.067753@0] init: try mount /dev/block/data to target /data
  889. [    9.090746@0] EXT4-fs (data): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
  890. [    9.094233@0] init: try mount /dev/block/cache to target /cache
  891. [    9.139810@0] EXT4-fs (cache): recovery complete
  892. [    9.143876@0] EXT4-fs (cache): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
  893. [    9.147765@0] init: cannot find '/system/bin/check_partition', disabling 'check_partition'
  894. [    9.155843@0] init: try mount rootfs to target /
  895. [    9.160587@0] init: try mount tmpfs to target /mnt/secure
  896. [    9.216546@1] set fail , detect locktable conflict,retry
  897. [    9.245171@0] init: cannot find '/system/bin/cdnclient', disabling 'cdnclient'
  898. [    9.282151@0] DSP pcmenc stream buffer to [0x9e401000-0x9e601000]
  899. [    9.292369@0] init: property 'ro.usb.vendor.string' doesn't exist while expanding '${ro.usb.vendor.string}'
  900. [    9.317044@0] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
  901. [    9.324055@0] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
  902. [    9.347037@0] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
  903. [    9.357096@0] android_usb:disable, not bind to controller
  904. [    9.360550@0] android_usb:disable, not bind to controller
  905. [    9.365387@0] android_usb:enable, not bind to controller
  906. [    9.380725@0] warning: `adbd' uses 32-bit capabilities (legacy support in use)
  907. root@android:/ # [    9.431986@0] Write AOBUS[0x0024]=0x0fff0fc3
  908. [   10.277665@1] kplayer_alsa_ad: open file:/fastplay/adconf.xml failed!
  909. [   14.686174@0] osd0=>x:1920 ,y:0,w:0,h:0
  910. [   14.686179@0]  osd1=> x:0,y:0,w:0,h:0
  911. [   14.718817@0] amvdec_h264 probe start.
  912. [   14.719026@0]
  913. [   14.719032@0] vh264_init
  914. [   14.728786@0] Alloc new mc addr to dea54000
  915. [   14.741674@0] vf_reg_provider:decoder.h264
  916. [   14.741792@0] vf_reg_provider:ppmgr
  917. [   14.778733@0] amvdec_h264 probe end.
  918. [   14.778868@0] tsdemux video_pid = 0x100, audio_pid = 0x101, sub_pid = 0xffff
  919. [   14.796496@0] v264dec: aspect_ratio not available from source
  920. [   14.796605@1] [dsp]dsp_open
  921. [   14.796611@1] audiodsp prevent sleep
  922. [   14.809788@1] [dsp]load firmware from userspace failed: switch to load it by calling request_firmware() in kernel
  923. [   14.900622@0] [dsp]load mcode size=148636
  924. [   14.900629@0] ,load addr 0xc4000000 mcode name audiodsp_codec_aac_helix.bindi_init_buf: version 2013-9-06a, prog_proc_type 0, buf start 8d200000, size 300000, buf(w720,h584) cur num 5 (available 5,  total 5)
  925. [   14.923424@0] vf_reg_provider:deinterlace
  926. [   14.931916@0] [dsp]DSP statck start =0x9e310000,size=0x10000
  927. [   14.934691@0] [dsp]DSP gp statck start =0x9e16b200,size=0x200
  928. [   14.947199@0] pre_de_buf_config: source change: 0/0/0/0=>36864/1920/1072/0
  929. [   14.978984@0] [dsp]DSP heap start =0x9e800000,size=0x100000
  930. [   14.986556@0] [dsp]DSP stream buffer to [0x9e328000-0x9e32ffe0]
  931. [   14.987203@0] reset dsp : dec opt=fffb, subid=0
  932. [   15.001437@0] [dsp]dsp reset now
  933. [   15.056516@0] [dsp]frame format changed,fmt->valid 0x1c
  934. [   15.056668@0] [dsp]audio info from dsp:sample_rate=48000 channel_num=2
  935. [   15.064938@0] [dsp]dsp status=52756e
  936. [   15.128044@0] substream#0 ptr: dfb72f00 type: playback name: subdevice #0 interface: I2S
  937. [   15.144953@0] ====== audio_set_aiubuf ======
  938. [   15.145077@0] I2S hw init,i2s mode 0
  939. [   15.157363@0] iec958 mode PCM16
  940. [   15.157512@0] IEC958 16bit
  941. [   15.157643@0] iec958 nodify hdmi audio type 1
  942. [   15.185667@0] audio info changed.notify to hdmi: type 1,sr 48000,ch 2
  943. [   15.186541@0] HDMI: aout notify rate 48000
  944. [   15.199841@0] HDMI: aout notify format PCM
  945. [   15.210770@0] audio pts started::::::: 0
  946. [   15.212774@0] audio pts started::::::: 1
  947. [   15.267283@1] HDMI: audio channel num is 1
  948. [   15.267377@1] current VIC: 4
  949. [   15.268649@1] audio sample rate: 3
  950. [   15.272016@1] HDMI: reset audio N para
  951. [   15.284625@1] PCM out to HDMI
  952. [   15.284700@1] i2s_to_spdif_flag:1
  953. [   15.285350@1] Enable audio spdif to HDMI
  954. [   15.301310@1] HDMI Audio Type: PCM
  955. [   15.301407@1] HDMI: set audio param
  956. [   15.607166@1] [887]reset apts:0x22803-->0x2a03f, pcr 0x22803, diff 30780
  957. [   19.502255@0] 333000
  958. [   21.171889@0] request_suspend_state: wakeup (3->0) at 20905040005 (1970-01-02 00:00:01.798658999 UTC)
  959. [   21.310095@1] trun off vdac
  960. [   21.460118@0] netdev_open
  961. [   21.460204@0] Ethernet reset
  962. [   21.460273@0] NET MDA descpter start addr=de194000
  963. [   21.468495@0] phy_reset!
  964. [   21.468527@0] set_phy_mode() phy_Identifier: 0x7c0f1
  965. [   21.474023@0] --1--write mac add to:df9a6748: c8 0e 77 02 5b db |..w.[.|
  966. [   21.478923@0] name=nand_key nand_key
  967. [   21.482618@0] read:addr:0xfe000000,phy_blk_addr:1016,phy_page_addr:0,aml_nand_get_key:129
  968. [   21.495928@0] unkown current key-name,key_read_show:1273
  969. [   21.496037@0] ret = -22
  970. [   21.496040@0] print_buff=
  971. [   21.513211@0] --2--write mac add to:df9a6748: c8 0e 77 02 5b db |..w.[.|
  972. [   21.514336@0] write mac add to:df9a6748: c8 0e 77 02 5b db |..w.[.|
  973. [   21.521685@0] Current DMA mode=0, set mode=621c100
  974. [   21.528291@0] ether leave promiscuous mode
  975. [   21.529463@0] ether leave all muticast mode
  976. [   21.533565@0] changed the Multicast,mcount=1
  977. [   21.537847@0] add mac address:33:33:00:00:00:01,bit=1
  978. [   21.542852@0] set hash low=2,high=0
  979. [   21.546355@0] changed the filter setting to :4
  980. [   21.552598@0] changed the Multicast,mcount=1
  981. [   21.555022@0] add mac address:33:33:00:00:00:01,bit=1
  982. [   21.564352@0] changed the Multicast,mcount=2
  983. [   21.564375@0] add mac address:33:33:00:00:00:01,bit=1
  984. [   21.564383@0] add mac address:01:00:5e:00:00:01,bit=32
  985. [   21.564388@0] set hash low=2,high=1
  986. [   21.564392@0] changed the filter setting to :4
  987. [   21.564772@0] ADDRCONF(NETDEV_UP): eth0: link is not ready
  988. [   21.632711@1] changed the Multicast,mcount=2
  989. [   21.632789@1] add mac address:33:33:00:00:00:01,bit=1
  990. [   21.636419@1] add mac address:01:00:5e:00:00:01,bit=32
  991. [   21.673595@1] init: no such service 'wififix'
  992. [   21.768960@1] +++dhd_module_init+++
  993. [   21.769288@1] [extern_wifi_set_enable] in
  994. [   21.770859@1] WIFI  Disenable!
  995. [   21.976876@1] [extern_wifi_set_enable] in
  996. [   21.976968@1] WIFI  Enable!
  997. [   22.367022@1] [extern_wifi_set_enable] in
  998. [   22.367138@1] WIFI  Enable!
  999. [   22.368342@1] [extern_wifi_set_enable] in
  1000. [   22.372288@1] WIFI  Enable!
  1001. [   22.375194@1]
  1002. [   22.375203@1] SD/MMC initialization started......
  1003. [   23.016972@1] mmc data3 pull high
  1004. [   23.017318@0] sd_mmc_info->card_type=0
  1005. [   23.018432@0] begin SDIO check ......
  1006. [   23.022918@0] Actual delay time in sdio_voltage_validation() = 10 ms
  1007. [   23.087350@1] Got RCA = 1
  1008. [   23.089457@0] #this sdio card could not support read after write
  1009. [   23.090615@0] sd_mmc_init() is completed successfully!
  1010. [   23.095635@0] This SDIO card is working in Wide Bus and at 50MHz High Speed mode!
  1011. [   23.095653@0]
  1012. [   23.108526@0] memorycard0: queuing unknown CIS tuple 0x80 (2 bytes)
  1013. [   23.111106@0] memorycard0: queuing unknown CIS tuple 0x80 (3 bytes)
  1014. [   23.116956@1] monitor : INSERT
  1015. [   23.120903@0] memorycard0: queuing unknown CIS tuple 0x80 (3 bytes)
  1016. [   23.128380@1] memorycard0: queuing unknown CIS tuple 0x80 (7 bytes)
  1017. [   23.176955@1] =========== WLAN placed in POWER ON ========
  1018. [   23.178128@1] bcmsdh_register: Linux Kernel SDIO/MMC Driver
  1019. [   23.182527@1] dhd_customer_oob_irq_map: customer specific Host GPIO number is (100)
  1020. [   23.190918@0] dhdsdio_probe : no mutex held. set lock
  1021. [   23.195591@0] F1 signature read @0x18000000=0x1591a962
  1022. [   23.257024@0] bcmsdh_config_hw_oob_intr: Enable HW OOB for 43362
  1023. [   23.262825@0] DHD: dongle ram size is set to 245760(orig 245760)
  1024. [   23.264559@0] dhd_bus_select_firmware_name_by_chip: firmware_path=/etc/wifi/40181/stable/fw_bcm40181a2.bin
  1025. [   23.275994@0] wl_create_event_handler thr:e5a created
  1026. [   23.279290@0] wl_create_event_handler thr:e5a started
  1027. [   23.289952@1] p2p0: P2P Interface Registered
  1028. [   23.290292@1] dhd_attach thr:e61 created
  1029. [   23.294164@1] dhd_attach thr:e61 started
  1030. [   23.296796@1] dhd_attach thr:e62 created
  1031. [   23.304542@1] dhd_attach thr:e62 started
  1032. [   23.305058@1] dhd_attach thr:e63 created
  1033. [   23.309340@1] dhd_attach thr:e63 started
  1034. [   23.315271@0] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33
  1035. [   23.321204@0] dhdsdio_probe : the lock is released.
  1036. [   23.326407@1] mylin s1 num=2
  1037. [   23.331380@0]
  1038. [   23.331393@0] Dongle Host Driver, version 1.28.23.5 (r)
  1039. [   23.331397@0] Compiled in drivers/net/wireless/bcmdhd on May 13 2014 at 09:49:34
  1040. [   23.447651@0] =========== WLAN placed in RESET ========
  1041. [   23.447694@0] ---dhd_module_init---
  1042. [   25.399020@1] dhd_bus_select_firmware_name_by_chip: firmware_path=/etc/wifi/40181/stable/fw_bcm40181a2.bin
  1043. [   25.403209@1]
  1044. [   25.403225@1] Dongle Host Driver, version 1.28.23.5 (r)
  1045. [   25.403238@1] Compiled in drivers/net/wireless/bcmdhd on May 13 2014 at 09:49:34
  1046. [   25.419601@1] wl_android_wifi_on in
  1047. [   25.525363@1] =========== WLAN going back to live  ========
  1048. [   25.525663@0]
  1049. [   25.525666@0]
  1050. [   25.525668@0] dhd_bus_deVReset: == WLAN ON ==
  1051. [   25.534446@0] dhd_bus_devreset called when dongle is not in reset
  1052. [   25.539361@0] Will call dhd_bus_start instead
  1053. [   25.543495@0] bcmsdh_config_hw_oob_intr: Enable HW OOB for 43362
  1054. [   25.549828@0] dhd_bus_select_firmware_name_by_chip: firmware_path=/etc/wifi/40181/stable/fw_bcm40181a2.bin
  1055. [   25.559556@0] Final fw_path=/etc/wifi/40181/stable/fw_bcm40181a2.bin
  1056. [   25.559572@0] Final nv_path=/etc/wifi/40181/stable/nvram.txt
  1057. [   25.559578@0] Final conf_path=/system/etc/firmware/config.txt
  1058. [   25.603145@0] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
  1059. [   25.836593@0] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
  1060. [   25.837230@0] bcmsdh_set_drvdata: Enter
  1061. [   25.840918@0] bcmsdh_register_oob_intr: Enter
  1062. [   25.845372@0] bcmsdh_register_oob_intr: IRQ=100 Type=414
  1063. [   25.855060@1] Set country ALL, revision 0
  1064. [   25.932228@1] Country code: ALL (ALL/0)
  1065. [   25.940135@1] ------ WIFI Firmware version = wl0: Jul  5 2013 17:55:22 version 5.90.195.89.10 FWID 01-f4d31c13
  1066. [   25.944568@1]   Driver: 1.28.23.5 (r)
  1067. [   25.944576@1]   Firmware: wl0: Jul  5 2013 17:55:22 version 5.90.195.89.10 FWID 01-f4d31c13
  1068. [   25.944629@1] wl_android_wifi_on: Success
  1069. [   25.945912@1] wl_cfg80211_attach_post: p2p0 p2p_dev_addr=02:22:f4:b5:67:2a
  1070. [   30.448099@0] osd0 free scale ENABLE
  1071. [   30.448237@0] vf_reg_provider:osd
  1072. [   30.459559@0] vf_light_unreg_provider:ppmgr
  1073. [   30.459596@0] ppmgr rebuild from light-unregister
  1074. [   30.460071@0] osd1 free scale ENABLE
  1075. [   30.477232@1] osd0=>x:0 ,y:0,w:0,h:0
  1076. [   30.477248@1]  osd1=> x:0,y:0,w:0,h:0
  1077. [   30.546944@0] <FIQ>:vf_ext_light_unreg_provide
  1078. [   30.546972@0] 0
  1079. [   30.554075@1] vf_unreg_provider:decoder.h264
  1080. [   30.554622@0] vf_unreg_provider:ppmgr
  1081. [   30.556758@0] vf_unreg_provider:deinterlace
  1082. [   30.577000@1] pts missed 10, pts hit 356, pts_outside 0, duration 3840, sync_outside 0, use_idr_framerate 0
  1083. [   30.582439@1] adec_release
  1084. [   30.583999@1] [dsp]dsp_release
  1085. [   30.587047@1] audiodsp allow sleep
  1086. [   30.660174@0] osd0=>x:0 ,y:0,w:1280,h:720
  1087. [   30.660189@0]  osd1=> x:0,y:0,w:18,h:18
  1088. [   30.710723@0] osd0 free scale ENABLE
  1089. [   30.710831@0] vf_reg_provider:osd
  1090. [   30.746933@0] <FIQ>:vf_ext_light_unreg_provide
  1091. [   30.746952@0] 0
  1092. [   32.001956@1] tvmode set to 720p
  1093. [   32.001976@1]
  1094. [   32.002087@1] don't set the same mode as current.
  1095. [   32.054898@1] osd0 free scale ENABLE
  1096. [   32.055009@1] vf_reg_provider:osd
  1097. [   32.060148@0] osd1 free scale ENABLE
  1098. [   32.105935@0] buf=0
  1099. [   32.105952@0]
  1100. [   32.106034@0] IEC958_mode_raw=0
  1101. [   32.146916@0] <FIQ>:vf_ext_light_unreg_provide
  1102. [   32.146938@0] 0
  1103. [   32.149409@1] osd[0] set scale, h_scale: DISABLE, v_scale: DISABLE
  1104. [   32.149437@1] osd[0].scaledata: 0 0 0 0
  1105. [   32.149457@1] osd[0].pandata: 0 1279 1080 1799
  1106. [   37.242796@0] trun off vdac
  1107. [   37.776021@1] BT_RADIO going: off
  1108. [   37.776103@1] BCM_BT: going OFF
  1109. [   37.815884@1] BT_RADIO going: on
  1110. [   37.815922@1] BCM_BT: going ON
  1111. [   37.886948@0] Changing baud from 0 to 115200
  1112. [   37.966954@0] Changing baud from 115200 to 115200
  1113. [   38.057658@0] Changing baud from 115200 to 2000000
  1114. [   38.496889@0] Changing baud from 2000000 to 115200
  1115. [   38.776936@0] Changing baud from 115200 to 2000000
  1116. [   39.173928@0] BT_RADIO going: off
  1117. [   39.173971@0] BCM_BT: going OFF
復制代碼

        嗯，TTL接口定義，有需要的拿去用。
C1s更換電源IC&加裝TTL插針實錄



完……
C1s更換電源IC&加裝TTL插針實錄

評分

參與人數 1威望 +1 金幣 +10 收起 理由
人見百態 + 1 + 10 ZNDS有你更精彩：）

查看全部評分


上一篇：剛買的new c1s 自帶2年會員， 客服說刷機就不是會員了
下一篇：樂視盒子ROOT及打開樂視盒子藍牙的簡單方法
推薦
發表于 2016-1-12 21:58 | 只看該作者 | 來自四川
大神，a31s求遙控移植方法，希望你賜教，朋友反應替換兩個文件不起作用強烈支持樓主ing……
回復 支持 1 反對 0

使用道具 舉報

推薦
發表于 2016-1-12 21:58 | 只看該作者 | 來自四川
大神，a31s求遙控移植方法，希望你賜教，朋友反應替換兩個文件不起作用
回復 支持 1 反對 0

使用道具 舉報

地板
 樓主| 發表于 2016-1-12 22:15 | 只看該作者 | 來自廣東
lhwxl2012 發表于 2016-1-12 21:58
大神，a31s求遙控移植方法，希望你賜教，朋友反應替換兩個文件不起作用強烈支持樓主ing…… ...

測得的碼貼上來看看。
回復 支持 反對

使用道具 舉報

5#
發表于 2016-1-13 08:48 | 只看該作者 | 來自陜西
大神，求遙控移植方法，希望你賜教，朋友反應替換兩個文件不起作用
回復 支持 反對

使用道具 舉報

6#
發表于 2016-1-13 09:33 | 只看該作者 | 來自江西
帖子精彩，受益匪淺，代碼太長了{:89:}
回復 支持 反對

使用道具 舉報

7#
發表于 2016-1-13 10:02 | 只看該作者 | 來自浙江
真是太牛逼了 完全看不懂
回復 支持 反對

使用道具 舉報

8#
發表于 2016-3-2 21:36 | 只看該作者 | 來自山東
樓主用心了，內容非常精彩。
回復 支持 反對

使用道具 舉報

9#
發表于 2016-4-5 21:41 | 只看該作者 | 來自山東
大神，看了您的帖子給C1s加TTL，但是接了VCC線，可能接反了導致燒了盒子，但是也不知道到底是哪個零部件燒壞了，求大神指點迷津，現在通電后什么燈也不亮。謝謝！
回復 支持 反對

使用道具 舉報

10#
發表于 2016-4-9 21:59 | 只看該作者 | 來自山東
很給力，ZNDS有你更精彩！
回復 支持 反對

使用道具 舉報

您需要登錄后才可以回帖 登錄 | 立即注冊

本版積分規則

Archiver|新帖|標簽|軟件|Sitemap|ZNDS智能電視網 ( 蘇ICP備2023012627號 )

網絡信息服務信用承諾書 | 增值電信業務經營許可證：蘇B2-20221768 丨 蘇公網安備 32011402011373號

GMT+8, 2024-11-15 15:11 , Processed in 0.121859 second(s), 16 queries , Redis On.

Powered by Discuz!

監督舉報：report#znds.com (請將#替換為@)

© 2007-2024 ZNDS.Com

快速回復 返回頂部 返回列表