X96MAX+救磚求助

trynda · 發表于 2021-3-15 14:44

本帖最后由 trynda 于 2021-3-15 21:55 編輯

X96MAX+ 4/32G的版本
主板是Q5X3_141 V4.1 20112
短接，USB，卡刷，全部救磚方法都無效，最終接了TTL，算是有點反應了，但鍵盤無法輸入。
哪位大佬知道怎么解嗎？
試了圖中幾個短接點都無效，懷疑是USB芯片燒壞了。
X96MAX+救磚求助

TTL輸出信息如下

SM1:BL:511f6b:81ca2f;FEAT:A0F83180:20282000;POC:F;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
bl2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0000 - pwm id 0x01
bl2_stage_init 0xc1
bl2_stage_init 0x02
L0:00000000
L1:00000703
L2:00008067
L3:15000020
S1:00000000
B2:20282000
B1:a0f83180
TE: 110403
BL2 Built : 15:21:48, Aug 28 2019. g12a g1bf2b53 - luan.yuan@droid15-sz
Board ID = 1
Set cpu clk to 24M
Set clk81 to 24M
Use GP1_pll as DSU clk.
DSU clk: 1200 Mhz
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot [url=home.php?mod=space&uid=103582]@[/url] 0
sw8 s
DDR driver_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 15:21:45
board id: 1
Load FIP HDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part : 0
fw parse done
Load ddrfw from eMMC, src: 0x00060200, des: 0xfffd0000, size: 0x0000c000, part: 0
Load ddrfw from eMMC, src: 0x00038200, des: 0xfffd0000, size: 0x00004000, part: 0
PIEI prepare done
fastboot data load
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000 , part: 0
00000000
emmc switch 0 ok
fastboot data verify
verify result: 265
Cfg max: 5, cur: 1. Board id: 255. Force loop cfg
DDR4 probe
ddr clk to 912MHz
Load ddrfw from eMMC, src: 0x00014200, des: 0xfffd0000, size: 0x0000c000, part: 0
dmc_version 0001
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : ERROR : Training has failed!
1D training failed
Cfg max: 5, cur: 2. Board id: 255. Force loop cfg
DDR3 probe
ddr clk to 792MHz
Load ddrfw from eMMC, src: 0x0002c200, des: 0xfffd0000, size: 0x0000c000, part: 0
dmc_version 0001
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 13:53:31
auto size-- 65535DDR cs0 size: 4096MB
DDR cs1 size: 0MB
DMC_DDR_CTRL: 0000002dDDR size: 3928MB
cs0 DataBus test pass
cs0 AddrBus test pass
100bdlr_step_size ps== 404
result report
boot times 0Enable ddr reg access
00000000
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
00000000
emmc switch 0 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part : 0
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000c8000, part: 0
bl2z: ptr: 05129330, size: 00001e40
0.0;M3 CHK:0;cm4_sp_mode 0
MVN_1=0x00000000
MVN_2=0x00000000
[Image: g12a_v1.1.3390-6ac5299 2019-09-26 14:09:46 luan.yuan@droid15-sz]
OPS=0x10
ring efuse init
2b 0c 10 00 01 2a 21 00 00 10 32 32 56 52 52 50
[0.017354 Inits done]
secure task start!
high task start!
low task start!
run into bl31
NOTICE: BL31: v1.3(release):4fc40b1
NOTICE: BL31: Built : 15:57:33, May 22 2019
NOTICE: BL31: G12A normal boot!
NOTICE: BL31: BL33 decompress pass
ERROR: Error initializing runtime service opteed_fast
U-Boot 2015.01 (Aug 17 2020 - 19:26:30)
DRAM: 3.8 GiB
Relocation Offset is: d6e5e000
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 00000000d7f3ec88
NAND: get_sys_clk_rate_mtd() 290, clock se**ng 200!
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 290, clock se**ng 200!
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC: aml_priv->desc_buf = 0x00000000d3e4ea70
aml_priv->desc_buf = 0x00000000d3e50db0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 40000000
aml_sd_retry_refix[983]:delay = 0x0,gadjust =0x142000
[mmc_startup] mmc refix success
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
Multi dtb tool version: v2 .
Support 4 dtbs.
aml_dt soc: sm1 platform: ac213 variant: 4g
dtb 0 soc: g12a plat: u212 vari: 2g
dtb 1 soc: g12a plat: u212 vari: 4g
dtb 2 soc: sm1 plat: ac213 vari: 2g
dtb 3 soc: sm1 plat: ac213 vari: 4g
Find match dtb: 3
start dts,buffer=00000000d3e53620,dt_addr=00000000d3e53620
get_partition_from_dts() 91: ret 0
Amlogic multi-dtb tool
Single dtb detected
parts: 17
00: logo 0000000000800000 1
01: recovery 0000000001800000 1
02: misc 0000000000800000 1
03: dtbo 0000000000800000 1
04: cri_data 0000000000800000 2
05: param 0000000001000000 2
06: boot 0000000001000000 1
set has_boot_slot = 0
07: rsv 0000000001000000 1
08: metadata 0000000001000000 1
09: vbmeta 0000000000200000 1
10: tee 0000000002000000 1
11: vendor 0000000046000000 1
12: odm 0000000008000000 1
13: system 0000000050000000 1
14: product 0000000008000000 1
15: cache 0000000046000000 2
16: data ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x4d400000
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3477: calc fbcc1098, store fbcc1098
_verify_dtb_checksum()-3477: calc fbcc1098, store fbcc1098
dtb_read()-3694: total valid 2
update_old_dtb()-3675: do nothing
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
Multi dtb tool version: v2 .
Support 4 dtbs.
aml_dt soc: sm1 platform: ac213 variant: 4g
dtb 0 soc: g12a plat: u212 vari: 2g
dtb 1 soc: g12a plat: u212 vari: 4g
dtb 2 soc: sm1 plat: ac213 vari: 2g
dtb 3 soc: sm1 plat: ac213 vari: 4g
Find match dtb: 3
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
cvbs: cpuid:0x2b
Net: Phy 0 not found
PHY reset timed out
[KM]Error:f[keymanage_dts_get_key_device]L105:eth_exphy_para key name is not exi st
[KM]Error:f[_get_km_ops_by_name]L248:key eth_exphy_para not know device 4
[KM]Error:f[key_unify_read]L312:key[eth_exphy_para] no cfg in dts

復制代碼

執筆畫僮 · 發表于 2021-3-16 15:03

我的也一樣，廢了，樓主能解決的話，分享一下，祝都能解決

吃雞和平使者 · 發表于 2021-3-15 15:07

X96 MAX+救磚教程。。。。。http://m.81jnr2m.cn/tv-1163052-1-1.html

trynda · 發表于 2021-3-15 18:35

吃雞和平使者發表于 2021-3-15 15:07
X96 MAX+救磚教程。。。。。http://m.81jnr2m.cn/tv-1163052-1-1.html

- - ！試了都失敗

despotical · 發表于 2021-3-15 21:22

新版的短接位置不一樣了

trynda · 發表于 2021-3-15 22:22

despotical 發表于 2021-3-15 21:22
新版的短接位置不一樣了

能試的短接點都試過了

yehuameng · 發表于 2021-3-16 16:50

在線收

trynda · 發表于 2021-3-17 06:26

本帖最后由 trynda 于 2021-3-17 06:27 編輯

執筆畫僮發表于 2021-3-16 15:03
我的也一樣，廢了，樓主能解決的話，分享一下，祝都能解決

準備工作：
1.用Burn Card Maker制作一張Slimbox的卡刷TF卡，注意要勾選擦除Bootloader。如果要刷官方的，可以將內存卡里的img文件換成官方的img，名字改成一樣的就可以偷梁換柱。
2.盒子的TTL接口在主板上HDMI接口旁邊，接口被堵了錫，要用電烙鐵清理一下。

救磚過程：
1.插入TF卡到盒子。
2.盒子接上TTL線到電腦，打開SecureCRT或Putty僅作為監看，不在這里執行任何操作。
3.插上電源和USB 3.0公對公的線（僅供電，無數據傳輸）。

順利的話，盒子會開始卡刷，SecureCRT會顯示進度。刷完后重啟就成功救磚了。

因?yàn)槭窍拐垓v給弄好的，不確定哪些操作是多余的。

我猜的“用USB給盒子供電就會觸發卡刷”你可以先試試只插TF和USB3.0看看，不行再接電源，再不行就接TTL，再不行就捅復位鍵。實在不行就隨機組合瞎折騰吧，我也是無意中救活的，全網無任何案例提及我這種方法。

556999394 · 發表于 2021-3-17 12:44

我一直連接不上電腦就是了

trynda · 發表于 2021-3-25 12:01

556999394 發表于 2021-3-17 12:44
我一直連接不上電腦就是了

樓上給出方法了，我也是完全沒連上電腦救活的

› 智能電視盒 / 安卓TV機頂盒區 › 外貿原生安卓盒子

X96MAX+救磚求助

X96MAX+救磚求助

相關帖子