首頁 收藏 QQ群
 網站導航

ZNDS智能電視網 推薦當貝市場

TV應用下載 / 資源分享區

軟件下載 | 游戲 | 討論 | 電視計算器

綜合交流 / 評測 / 活動區

交流區 | 測硬件 | 網站活動 | Z幣中心

新手入門 / 進階 / 社區互助

新手 | 你問我答 | 免費刷機救磚 | ROM固件

查看: 122425|回復: 21
上一主題 下一主題
[教程&攻略]

小米盒子4S Pro TTL調試

  [復制鏈接]
跳轉到指定樓層
樓主
發表于 2020-11-18 13:48 | 只看該作者 |只看大圖 回帖獎勵 |倒序瀏覽 |閱讀模式 | 來自浙江
小米盒子4S Pro網上資料比較少，只能自己拆機查看了
拆機發現板子非常簡陋，板子連TF卡槽都取消了，主板上有一個未焊接的3腳焊盤位，應該就是TTL，接上測試可以進行調試，系統uboot可以進入，系統命令行操作是關閉的，無法進入，不過能進入Uboot感覺還是可以玩玩的，說不定可以USB啟動外部系統

簡陋的主板照：

小米盒子4S Pro TTL調試

小米盒子4S Pro TTL調試

TTL接口，如果沒有啟動信息可能是TX，RX標反了，反接一下即可

小米盒子4S Pro TTL調試

小米盒子4S Pro TTL調試

詳細的TTL信息：
  1. SM1:BL:511f6b:81ca2f;FEAT:B0F971B0:20292020;POC:F;RCY:0;EMMC:0;READ:0;0.0;0.0;CHK:0;
  2. bl2_stage_init 0x01
  3. bl2_stage_init 0x81
  4. hw id: 0x0000 - pwm id 0x01
  5. bl2_stage_init 0xc1
  6. bl2_stage_init 0x02

  8. L0:0000000f
  9. L1:00000700
  10. L2:00008067
  11. L3:15000020
  12. S1:00000000
  13. B2:20292020
  14. B1:b0f971b0

  16. TE: 514704

  18. BL2 Built : 13:38:54, Oct 10 2020. g12a g92322cd - shuai.wu@xiaomi

  20. Board ID = 0
  21. Set cpu clk to 24M
  22. Set clk81 to 24M
  23. Use GP1_pll as DSU clk.
  24. DSU clk: 1200 Mhz
  25. CPU clk: 1800 MHz
  26. Set clk81 to 166.6M
  27. eMMC boot [url=home.php?mod=space&uid=103582]@[/url] 0
  28. sw8 s
  29. board id: 0
  30. Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
  31. fw parse done
  32. PIEI prepare done
  33. 00000000
  34. emmc switch 1 ok
  35. 00000000
  36. emmc switch 2 ok
  37. NO find ddr boot_info from eMMC
  38. fastboot data verify
  39. result: 255
  40. Cfg max: 12, cur: 1. Board id: 255. Force loop cfg
  41. DDR4 probe

  43. LPDDR4_PHY_V_0_1_21-Built : 15:37:51, Mar 26 2020. g12a gf098346 - gongwei.chen@droid11-sz
  44. ddr clk to 1320MHz
  45. 00000000
  46. emmc switch 0 ok

  48. dmc_version 0001
  49. Check phy result
  50. INFO : End of initialization
  51. INFO : End of read enable training
  52. INFO : End of fine write leveling
  53. INFO : ERROR : Training has failed!
  54. 1D training failed
  55. Cfg max: 12, cur: 2. Board id: 255. Force loop cfg
  56. DDR4 probe
  57. ddr clk to 1320MHz

  59. dmc_version 0001
  60. Check phy result
  61. INFO : End of initialization
  62. INFO : End of read enable training
  63. INFO : End of fine write leveling
  64. INFO : End of read dq deskew training
  65. INFO : End of MPR read delay center optimization
  66. INFO : End of Write leveling coarse delay
  67. INFO : End of write delay center optimization
  68. INFO : End of read delay center optimization
  69. INFO : End of max read latency training
  70. INFO : Training has run successfully!
  71. 1D training succeed
  72. Check phy result
  73. INFO : End of initialization
  74. INFO : End of 2D read delay Voltage center optimization
  75. INFO : End of 2D write delay Voltage center optimization
  76. INFO : Training has run successfully!

  78. soc_VRef_reg_value 0x 00000032 00000030 0000002b 0000002f 0000002d 0000002d 00000032 0000002f 0000002d 00000030 0000002e 00000030 0000002a 0000002f 00000031 0000002d 00000034 00000031 0000002f 0000002b 0000002e 0000002f 0000002e 00000030 0000002c 0000002c 00000032 00000031 0000002f 0000002a 00000032 0000002f dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0001
  79. dram_vref_reg_value 0x 0000001a
  80. 2D training succeed
  81. auto size-- 65535DDR cs0 size: 2048MB
  82. DDR cs1 size: 0MB
  83. DMC_DDR_CTRL: 0050002cDDR size: 2048MB
  84. cs0 DataBus test pass
  85. cs0 AddrBus test pass

  87. non-sec scramble use zero key
  88. ddr scramble enabled

  90. 100bdlr_step_size ps== 440
  91. result report
  92. boot times 0Enable ddr reg access
  93. 00000000
  94. emmc switch 3 ok
  95. BL2: rpmb counter: 0x0000001c
  96. 00000000
  97. emmc switch 0 ok
  98. Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
  99. Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x0013aa00, part: 0
  100. 0.0;0.0;M3 CHK:0;cm4_sp_mode 0
  101. [Image: g12a_v1.1.3395-4f61cc3 2020-09-21 11:08:04 shuai.wu@xiaomi]
  102. OPS=0x03
  103. ring efuse init
  104. 2b 0b 03 00 01 11 2a 00 00 11 31 36 41 34 56 50
  105. [0.050490 Inits done]
  106. secure task start!
  107. high task start!
  108. low task start!
  109. boot bl31
  110. NOTICE:  BL31: v1.3(release):61f890e5e
  111. NOTICE:  BL31: Built : 15:09:20, Sep 16 2020
  112. NOTICE:  BL31: G12A secure boot!
  113. NOTICE:  BL31: BL33 decompress pass
  114. INFO:    BL3-2: ATOS-V2.4.4-30-g921539e #1 Fri Dec 6 01:21:23 2019 -0700 arm
  115. INFO:    BL3-2: Chip: SM1 Rev: B (2B:B - 0:2)
  116. INFO:    BL3-2: crypto engine DMA
  117. INFO:    BL3-2: secure time TEE
  118. INFO:    BL3-2: CONFIG_DEVICE_SECURE 0xb200000e


  121. U-Boot 2015.01-g6223619 (Oct 19 2020 - 14:52:47), Build: jenkins-uboot_frozen_release-2

  123. DRAM:  1 GiB
  124. Relocation Offset is: 36d89000
  125. mmu cfg end: 0x40000000
  126. mmu cfg end: 0x40000000
  127. register usb cfg[0][1] = 0000000037ea4890
  128. gpio: pin GPIOAO_11 (gpio 11) value is 1
  129. InUsbBurn
  130. wait for phy ready count is 0
  131. noSof
  132. sof timeout, reset usb phy tuning
  133. gpio: pin GPIOX_6 (gpio 86) value is 1
  134. MMC:   aml_priv->desc_buf = 0x0000000033d7a0c0
  135. aml_priv->desc_buf = 0x0000000033d7c400
  136. SDIO Port B: 0, SDIO Port C: 1
  137. co-phase 0x3, tx-dly 0, clock 400000
  138. co-phase 0x3, tx-dly 0, clock 400000
  139. co-phase 0x3, tx-dly 0, clock 400000
  140. emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
  141. emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
  142. co-phase 0x3, tx-dly 0, clock 400000
  143. co-phase 0x3, tx-dly 0, clock 40000000
  144. [set_emmc_calc_fixed_adj][875]find fixed adj_delay=20
  145. init_part() 297: PART_TYPE_AML
  146. [mmc_init] mmc init success
  147. aml log : R2048 check pass!
  148.       Amlogic multi-dtb tool
  149.       Single dtb detected
  150. start dts,buffer=0000000001000000,dt_addr=0000000001000000
  151. get_partition_from_dts() 92: ret 0
  152.       Amlogic multi-dtb tool
  153.       Single dtb detected
  154. parts: 17
  155. 00:      logo   0000000000800000 1
  156. 01:  recovery   0000000001800000 1
  157. 02:      misc   0000000000800000 1
  158. 03:      dtbo   0000000000800000 1
  159. 04:  cri_data   0000000000800000 2
  160. 05:     param   0000000001000000 2
  161. 06:      boot   0000000001000000 1
  162. set has_boot_slot = 0
  163. 07:       rsv   0000000001000000 1
  164. 08:  metadata   0000000001000000 1
  165. 09:    vbmeta   0000000000200000 1
  166. 10:       tee   0000000002000000 1
  167. 11:factorydata  0000000000a00000 2
  168. 12:    vendor   0000000020000000 1
  169. 13:    system   0000000040000000 1
  170. 14:   product   0000000002000000 1
  171. 15:     cache   0000000020000000 2
  172. 16:      data   ffffffffffffffff 4
  173. init_part() 297: PART_TYPE_AML
  174. eMMC/TSD partition table have been checked OK!
  175. crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
  176. crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
  177. crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
  178. mmc env offset: 0x27400000
  179. aml log : internal sys error!
  180. reboot_mode=cold_boot
  181. amlkey_init() enter!
  182. [EFUSE_MSG]keynum is 4
  183. vpu: driver version: v20190313
  184. vpu: detect chip type: 11
  185. vpu: clk_level default: 7(666667000Hz), max: 7(666667000Hz)
  186. vpu: clk_level in dts: 7
  187. vpu: vpu_power_on
  188. vpu: set_vpu_clk
  189. vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
  190. vpu: set_vpu_clk finish
  191. vpu: vpu_module_init_config
  192. vpp: vpp_init
  193. vpp: vpp osd2 matrix rgb2yuv..............
  194. hdr_func 4, hdr_process_select 0x1
  195. gpio: pin GPIOH_7 (gpio 38) value is 1
  196. cvbs: cpuid:0x2b
  197. cvbs: find performance_pal config
  198. aml log : internal sys error!
  199. pll tsensor avg: 0x1f9b, u_efuse: 0x2b
  200. temp1: 36
  201. ddr tsensor avg: 0x1f9c, u_efuse: 0x53
  202. temp2: 37
  203. device cool done
  204. hpd_state=0
  205. do_hpd_detect: hdmimode=2160p60hz
  206. do_hpd_detect: colorattribute=420,8bit
  207. Saving Environment to aml-storage...
  208. mmc env offset: 0x27400000
  209. Writing to MMC(1)... done
  210. no sink, fallback to 720p60hz[4]
  211. hdr mode is 0
  212. dv  mode is ver:0  len: 0
  213. hdr10+ mode is 0
  214. read hdmichecksum 0x00000000, colorattribute 420,8bit
  215. read hdmimode 2160p60hz, colorspace <NULL>, colordepth <NULL>
  216. do_get_parse_edid: autoMode = false, manualMode=97
  217. isYuv4KSink: false, maxTMDSRate=150
  218. do_get_parse_edid: non-yuv4k sink: inColorSpace: HDMI_COLOR_FORMAT_RGB
  219. do_get_parse_edid: default inColorDepth: HDMI_COLOR_DEPTH_24B
  220. TV is same, initial mode is: 576cvbs attr: 420,8bit
  221. dolby_status 0
  222. dolby_status 0
  223. dolby_vision_process: no tv and dv disabled
  224. Saving Environment to aml-storage...
  225. mmc env offset: 0x27400000
  226. Writing to MMC(1)... done
  227. [OSD]load fb addr from dts:/meson-fb
  228. [OSD]load fb addr from dts:/fb
  229. [OSD]set initrd_high: 0x7f800000
  230. [OSD]fb_addr for logo: 0x7f800000
  231. [OSD]load fb addr from dts:/meson-fb
  232. [OSD]load fb addr from dts:/fb
  233. [OSD]fb_addr for logo: 0x7f800000
  234. [OSD]VPP_OFIFO_SIZE:0xfff01fff
  235. [CANVAS]canvas init
  236. [CANVAS]addr=0x7f800000 width=3840, height=2160
  237. [OSD]osd_hw.free_dst_data: 0,719,0,575
  238. [OSD]osd1_update_disp_freescale_enable
  239. vpp: vpp_matrix_update: 2
  240. cvbs_performance_enhancement
  241. cvbs_config_hdmipll_g12a
  242. cvbs_set_vid2_clk
  243. dolby_status 0
  244. dolby_status 0
  245. hdr_packet
  246. vpp: hdr_policy = 0
  247. vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
  248. s_version: U-Boot 2015.01-g6223619
  249. Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
  250. co-phase 0x3, tx-dly 0, clock 40000000
  251. co-phase 0x3, tx-dly 0, clock 40000000
  252. co-phase 0x3, tx-dly 0, clock 400000
  253. emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
  254. emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
  255. co-phase 0x3, tx-dly 0, clock 400000
  256. co-phase 0x3, tx-dly 0, clock 40000000
  257. [set_emmc_calc_fixed_adj][875]find fixed adj_delay=20
  258. init_part() 297: PART_TYPE_AML
  259. [mmc_init] mmc init success
  260. switch to partitions #0, OK
  261. mmc1(part 0) is current device
  262. do_factorydata_read:204 Can't find out assm_mn from factorydata.
  263. factorydata - Access the factorydata from Xiaomi Partition

  265. Usage:
  266. factorydata     argv:
  267.     dump
  268.     read keyname
  269.     write keyname value
  270.     erase keyname

  272. do_factorydata_read:204 Can't find out loglevel from factorydata.
  273. factorydata - Access the factorydata from Xiaomi Partition

  275. Usage:
  276. factorydata     argv:
  277.     dump
  278.     read keyname
  279.     write keyname value
  280.     erase keyname

  282. do_factorydata_read:204 Can't find out console_enable from factorydata.
  283. factorydata - Access the factorydata from Xiaomi Partition

  285. Usage:
  286. factorydata     argv:
  287.     dump
  288.     read keyname
  289.     write keyname value
  290.     erase keyname

  292. Command: bcb uboot-command
  293. Start read misc partition datas!
  294. BCB hasn't any datas,exit!
  295. do_monitor_bt_cmdline
  296. USB0:   USB3.0 XHCI init start
  297. Register 3000140 NbrPorts 2
  298. Starting the controller
  299. USB XHCI 1.10
  300. scanning bus 0 for devices... 3 USB Device(s) found
  301. udev->descriptor.idVendor:0xbda udev->descriptor.idProduct:0xc820
  302. enumerate rtk usb dev OK usb_port:1
  303. bt_cmdline: start to download fw
  304. bt_cmdline: fw downloaded
  305. rtk_set_wake_polarity, polarity=0
  306. hci_set_scan_enable
  307. no recovery mod!
  308. rc scan end
  309. [imgread]szTimeStamp[2020102104463406]
  310. [imgread]secureKernelImgSz=0x91d800
  311. aml log : R~2048 check pass!
  312. aml log : R2048 check pass!
  313. aml log : R2048 check pass!
  314. avb2: 0
  315. ee_gate_off ...
  316. avb2: 0
  317. ## Booting Android Image at 0x01080000 ...
  318. Kernel command line: androidboot.dtbo_idx=0 buildvariant=user
  319. [store]Is good fdt check header, no need decrypt!
  320. load dtb from 0x1000000 ......
  321.       Amlogic multi-dtb tool
  322.       Single dtb detected
  323.    Loading Kernel Image(COMP_NONE) ... OK
  324.    kernel loaded at 0x01080000, end = 0x01989000
  325. libfdt fdt_getprop(): FDT_ERR_NOTFOUND
  326.    Loading Device Tree to 0000000009fea000, end 0000000009fffbbc ... OK
  327. fdt_fixup_memory_banks, reg:0000000000000000

  329. Starting kernel ...

  331. uboot time: 10220517 us
  332. [    0.000000@0] Linux version 4.9.113-g0ba0888-dirty (jenkins@c5-mitv-bsp-build07.bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Wed Oct 21 04:30:00 CST 2020
  333. [    0.000000@0] Reserved memory: regions without no-map are not yet supported
  334. [    0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 hdr_policy=0 hdr_priority= reboot_mode_android=normal logo=osd0,loaded,0x3d800000 vout=576cvbs,enable hdmitx=,420,8bit hdmimode=2160p60hz hdmichecksum=0x00000000 dolby_vision_on=0 frac_rate_policy=1 hdmi_read_edid=1 cvbsmode=576cvbs osd_reverse=0 video_reverse=0 irq_check_en=0 androidboot.firstboot=0 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01-g6223619 androidboot.build.expect.baseband=N/A androidboot.reboot_mode=cold_boot androidboot.platform_id=216 androidboot.mi.cpu=Cortex-A55 androidboot.mi.gpu=Mali-G31 androidboot.model_name=m23m_00_3f androidboot.provider=amlogic androidboot.serialno=30699800000001836 androidboot.mac=6c:0d:c4:0f:6e:0a quiet root=/dev/mmcblk0p18 ro rootwait skip_initramfs androidboot.selinux=enforcing otg_device=0 androidboot.dtbo_idx=0 build
  335. [    0.455892@0] vout: error: invalid vinfo1. current vmode is not supported
  336. [    0.457064@0] vout: error: invalid vinfo1. current vmode is not supported
  337. [    0.602556@1] meson_cpufreq_init:don't find the node <dynamic_gp1_clk>
  338. [    0.606573@1] ff803000.serial: clock gate not found
  339. [    0.747851@1] di_get_vpu_clkb: get clk vpu error.
  340. [    0.749132@1] get fclk_div5 err
  341. [    0.750031@1] vdin_drv_probe: vdin cannot get msr clk !!!
  342. [    0.755758@1] get fclk_div5 err
  343. [    0.758555@1] vdin_drv_probe: vdin cannot get msr clk !!!
  344. [    0.768861@1] pixel_probe: vpp probe func error!
  345. [    0.810889@0] cectx ff80023c.aocec: not find 'port_num'
  346. [    0.810936@0] cectx ff80023c.aocec: no hdmirx regs
  347. [    0.815271@0] cectx ff80023c.aocec: no hhi regs
  348. [    0.821827@0] cectx ff80023c.aocec: wakeup_reason:0x0
  349. [    0.857197@0] request_irq error ret=-22
  350. [    0.857258@0] dev_pm_set_wake_irq failed: -22
  351. [    0.861218@0] page_trace_module_init, create sysfs failed
  352. [    0.866034@0] defendkey ff630218.defendkey: Reserved memory is not enough!
  353. [    1.089421@0] asoc-aml-card auge_sound: control 2:0:0:I2SIn CLK:0 is already present
  354. [    1.091526@0] snd_tdm ff660000.audiobus:tdm@1: ASoC: Failed to add I2SIn CLK: -16
  355. [    1.098990@0] aml_dai_tdm_probe, failed add snd tdm controls
  356. [    1.104626@0] asoc-aml-card auge_sound: control 2:0:0:I2SIn CLK:0 is already present
  357. [    1.112379@0] snd_tdm ff660000.audiobus:tdm@2: ASoC: Failed to add I2SIn CLK: -16
  358. [    1.119799@0] aml_dai_tdm_probe, failed add snd tdm controls
  359. [    1.[    1.590270@3] EXT4-fs (mmcblk0p18): couldn't mount as ext3 due to feature incompatibilities
  360. [    1.623333@3] usb 1-1: Unsupported device
  361. [    1.623707@3] usb 1-1: Unsupported device
  362. [    1.626047@3] usb 1-1: Unsupported device
  363. [    1.878156@2] init: waitid failed: No child processes
  364. [    1.878230@2] init: get_model_name: Model Name -> m23m_00_3f
  365. [    1.883446@2] init: get_model_property_ini : INI load file error, use default file
  366. [    2.055145@3] ueventd: /vendor/ueventd.rc: 110: /sys/ lines must have 5 entries
  367. [    3.626765@3] Amlogic A/V streaming port init
  368. [    4.418508@3] android.hardware.health@2.0-impl: wakealarm_init: timerfd_create failed
  369. [   12.760974@2] init: Boot Completed !!!
  370. [   12.761842@2] inyt: Can't create : File exists
  371. [   13.976602@2] rtk_btusb: reset_controller
  372. [   15.619288@0] rtk_btusb: btchr_ioctl:Failed with wrong Cmd:1074021809
  373. [   21.074753@2] init: No such service 'bdupdate' for ctl.stop
  374. [   21.078214@3] init: No such service 'sensord' for ctl.stop

復制代碼



上一篇：小米盒子4S Pro MDZ-26-AA TTL成功看圖告訴你TTL針腳在哪
下一篇：小米盒子MDZ-26-aa-s905x3-4S Pro emmc備份
推薦
發表于 2023-10-23 12:44 | 只看該作者 | 來自重慶
turkeycq 發表于 2023-6-19 14:56
我這個也是一樣。

ctrl+z
回復 支持 1 反對 0

使用道具 舉報

推薦
發表于 2022-7-9 18:18 | 只看該作者 | 來自山東
請問怎么用這個備份文件修磚 已經變磚了  獅子沒錢再買新的了  求求你們誰知道的 可以指點下嗎  唉
回復 支持 1 反對 0

使用道具 舉報

推薦
發表于 2020-12-2 23:17 來自ZNDS手機版 | 只看該作者 | 來自遼寧
aghfsj135 發表于 2020-11-18 14:23
最近準備買一個盒子，請問有哪些好的推薦

3增強版


回復 支持 1 反對 0

使用道具 舉報

沙發
發表于 2020-11-18 14:04 | 只看該作者 | 來自浙江
默默大神的新玩具已經變成零件了
回復 支持 反對

使用道具 舉報

板凳
發表于 2020-11-18 14:09 | 只看該作者 | 來自廣東
這個配置399，降價100快性價比都不算高
回復 支持 反對

使用道具 舉報

地板
發表于 2020-11-18 14:09 | 只看該作者 | 來自陜西
還在用3呢
回復 支持 反對

使用道具 舉報

5#
發表于 2020-11-18 14:10 | 只看該作者 | 來自云南
牛皮啊這么快到手開始拆了
回復 支持 反對

使用道具 舉報

6#
發表于 2020-11-18 14:11 | 只看該作者 | 來自江西
玩機大神的樂趣跟我們小白就是不一樣，直接拆機開干
回復 支持 反對

使用道具 舉報

7#
發表于 2020-11-18 14:20 | 只看該作者 | 來自重慶
4k都放不了，不如它爺爺
回復 支持 反對

使用道具 舉報

8#
發表于 2020-11-18 14:23 | 只看該作者 | 來自上海
最近準備買一個盒子，請問有哪些好的推薦
回復 支持 反對

使用道具 舉報

9#
發表于 2020-11-18 14:27 | 只看該作者 | 來自河南
要這么多代碼啊
回復 支持 反對

使用道具 舉報

您需要登錄后才可以回帖 登錄 | 立即注冊

本版積分規則

Archiver|新帖|標簽|軟件|Sitemap|ZNDS智能電視網 ( 蘇ICP備2023012627號 )

網絡信息服務信用承諾書 | 增值電信業務經營許可證：蘇B2-20221768 丨 蘇公網安備 32011402011373號

GMT+8, 2024-11-16 00:52 , Processed in 0.078871 second(s), 14 queries , Redis On.

Powered by Discuz!

監督舉報：report#znds.com (請將#替換為@)

© 2007-2024 ZNDS.Com

快速回復 返回頂部 返回列表