中興機頂盒B8601.1T TTL后跑碼無法輸入指令

xinxingezi · 發表于 2017-11-22 00:40

本帖最后由 wuli小茶于 2017-11-22 09:40 編輯

GXL:BL1:9ac50e:a1974b;FEAT:ADFD318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 266454

BL2 Built : 19:31:35, Jul 25 2017.
gxl g4bbe26f-dirty - liang.yang@droid11-sz

Board ID = 8, adc=619
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
Can't match board id, use default ddr_set[0]
DDR type: DDR3-ID
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz - PASS
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x00007400
Load bl301 from eMMC, src: 0x00018200, des: 0x01200000, size: 0x00002200
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000de200
NOTICE:  BL3-1: v1.0(debug):27d2eea5
NOTICE:  BL3-1: Built : 14:56:35, Mar 24 2017
aml log : bl31 normal boot !
[Image: gxl_v1.1.3090-c2794da-dirty 2017-06-23 15:25:47 yun.cai@droid03]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: ef be ad de d f0 ad ba ef be ad de not ES chip
efuse init ops = e2
efuse init hdcp = c, cf9=7
[0.777146 Inits done]
sINFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
rcu
e
.tUa-sBko ostt a2r0t1!5
y0hi1g-hg 7t4a4s1kb ds1t-adritr!t
  (loSwe pt a0s9k  s2t0a1r7t !-
17:53:13)

DRAM:  1 GiB
gpio: pin GPIOCLK_1 (gpio 99) value is 1
gpio: pin GPIOAO_6 (gpio 106) value is 1
reboot_mode=cold_boot

[BL31]: tee size: 0

Try USB burn

set osd_size 720p
bootmode:NORM
OK
uboot time: 2635910 us
[ 0.000000@0][ 0/swapp] Initializing cgroup subsys cpu
[ 0.000000@0][ 0/swapp] Initializing cgroup subsys cpuacct
[ 0.000000@0][ 0/swapp] CPU: ARMv71 Processor [410fd034] revision 4
[ 0.000000@0][ 0/swapp] no prop version_code
[ 0.000000@0][ 0/swapp] bootconsole [earlycon0] enabled
get_dvfs_info 0008
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ 1.1root@p200_2G:/ # [ 14.322965@0][ 5461/Threa] monitor: received netlink message:ztebw ok
[ 14.323765@0][ 5461/Threa] monitor:reply

上面是跑馬類容?？吹胶芏嗳说那笾彩沁@樣。求解！?。。?br />

wx_CxaOUaxZ · 發表于 2019-1-27 08:18

無法使用鍵盤的可以看看哦，
首先打開putty，左邊 Teeminal 點擊后后邊 implicit CR。。。。和 implicit LF。。。勾上
下面 Local echo 勾選 Force on 就行

iBinger · 發表于 2020-2-27 18:36

通過幾天的通宵達旦研究，無法輸入的原因找到了，是因為kernel啟動時，在init.rc里設置了：
setprop persist.service.consoleenable 0
然后再console服務啟動時是這樣的：
on property:persist.service.consoleenable=1
start console
on property:persist.service.consoleenable=0
start console
所以，你這輩子都不可能輸入指令了的，哈哈~
唯一的辦法就是重新做一個boot.img寫入進去；
如果你的盒子沒有第一句：setprop persist.service.consoleenable 0
你還可以用adb shell登錄進去，然后：
echo 1>/data/property/persist.service.consoleenable
然后重啟試試看

只是打醬油的 · 發表于 2017-12-12 18:41

我剛才也遇到這問題了，看最后的代碼也差不多……換電腦，換軟件各種方法都試了就是沒用，我開始以為是新版本無法破解了，差點放棄了……后來看到有說可能是線的問題，我還想都跑碼成功了怎么還會有這種可能……不過后來死馬當活馬醫，把用的三根線換了下……居然真的好了……emmmmm，大概你也可以試試

280353007 · 發表于 2019-2-23 21:41

wx_CxaOUaxZ 發表于 2019-1-27 08:18
無法使用鍵盤的可以看看哦，
首先打開putty，左邊 Teeminal 點擊后后邊 implicit CR。。。。和 implicit L ...

鍵盤能用，但是輸入命令也不起作用，是不是盒子受限制了？

jxawgy · 發表于 2018-1-6 18:30

?
ROM6716V1@jun  6 201610:51:31
MODE:EMMC
Jump

B16_COMP BL1 @May  8 2017
A53 down
pll ok!
W
ddr_W 1600M svn14110 finish
EMMC
chip id ERR
mN0^^: a53
mO0^^: B16_COMP
mT0^^: stby work high
ICE:  bl31_early_platform_setup
INFO: bl31_plat_arch_setup
NOTICE:  BL31: v1.2(debug):svn 16266
NOTICE:  BL31: Built : 09:55:24, Apr 12 2017
NOTICE:  B16XX
INFO: bl31_platform_setup
INFO: GICv3 without legacy support detected. ARM GICV3 driver initialized in EL3
INFO: BL31: Initializing runtime services
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x4f000000
INFO: SPSR = 0x3c5

U-Boot 2015.10-gf7f5fc4 (Sep 01 2017 - 18:23:33 +0800)

DRAM:  1 GiB
agpio13 =0 ,agpio6 =0
GPIO reset phy. GPIO = 136
MMC: eMMC: 0
Using default environment

In: serial
Out: serial
Err: serial
board_late_init
io_ctrl_idle_b16w23
zx_keycol2_keyrow1_pwm_init_table_1!
ZX_OTP_VDD_INFO = 1!
Net: CONFIG_ETH_DESIGNWARE_QOS_420
phy reset ok
confs rtn=0, g_enetaddr=28:8c:b8:cd:c4:58
dwmac.5200000
[setup_com_controlenv] COMControlFlag=> value[1]=0, val=0
## Error: Can't overwrite "ethaddr"
## Error inserting "ethaddr" variable, errno=1
zte_mac=00:02:f7:ef:00:02,ethaddr=00:02:f7:ef:00:02
Hit any key to stop autoboot:  0 in the 280*************
in thebootdelay=0************
in abort=0***********                                                       0

MMC read: dev # 0, block # 2179072, count 1 ... 1 blocks read: OK
misc:
***********val=0********************************

MMC read: dev # 0, block # 1867776, count 1 ... 1 blocks read: OK

MMC read: dev # 0, block # 1867776, count 388 ... 388 blocks read: OK
logo_load_addr is 0x77000000
[setup_bootenv] COMControlFlag=> value[9]=0, val=0
*******************MarketCodenew is 36**********
TVMode: val:0001000100080000
do_bootsys to boot NORM

MMC read: dev # 0, block # 2260992, count 2 ... 2 blocks read: OK

MMC read: dev # 0, block # 2260996, count 23509 ... 23509 blocks read: OK
kernel_addr in header:0x40008000

MMC read: dev # 0, block # 2284504, count 2621 ... 2621 blocks read: OK

MMC read: dev # 0, block # 2287124, count 261 ... 261 blocks read: OK
hw_ver
enable emmc rst n function:mmc rst 0 1

setenv bootargs root=/dev/ram0 rw initrd=0x41000000,0x1470b0 boardtype=0x13 console=ttyS0,115200n8 ${othbootargs} stmmaceth=chain_mode:1 kgdboc=ttyS0,115200 loglevel=3 swiotlb=0x800  androidboot.hardware=zxic androidboot.selinux=disabled boot_revision=V0033 market=36,1 LogoDataAddr=0x77000000 WorkMode=0 LogoDisplayModel=0 AutoOutputFlag=  HDMIAdaptiveMode=1 StandbyIRCode=  ProductID=1B100499007037200000288CB8CDC458 BootVideoCtrl=0 COMControlFlag=0 TVMode=0001000100080000 576DispInfo=0012001006990557 480DispInfo=0012001006980460 720DispInfo=0017000812450704 1080DispInfo=0019001018811058 4KDispInfo=0000000038402160
secure=0 board:b16w23
## Flattened Device Tree blob at 40e00000
Booting using the fdt blob at 0x40e00000
Using Device Tree in place at 0000000040e00000, end 0000000040e0a4f3

Starting kernel ...

[ 1.078189]  init_softpoweroff_sctrl: gpio software power-off reg = 0x1160a433
同樣的問題有高手解決嗎？

xinxingezi · 發表于 2017-11-22 10:07

hao501802766 發表于 2017-11-22 10:00
http://m.81jnr2m.cn/jc/article/17006-1.html
中興B860AV1.1-T2安裝教程

我就是按照這個教程跑的，跑出來的代碼，無法輸入指令，而且出來的指令明顯跟教程的不一樣

hao501802766 · 發表于 2017-11-22 10:00

xinxingezi 發表于 2017-11-22 09:47
試過，沒有效果，而且這個是1.1T 是1.1的升級版

http://m.81jnr2m.cn/jc/article/17006-1.html
中興B860AV1.1-T2安裝教程

hao501802766 · 發表于 2017-11-22 09:44

B860av1.1的應該都支持輸入試試拔插下U盤或者重新跑馬多按按回車鍵試試

xinxingezi · 發表于 2017-11-22 09:47

hao501802766 發表于 2017-11-22 09:44
B860av1.1的應該都支持輸入試試拔插下U盤或者重新跑馬多按按回車鍵試試

試過，沒有效果，而且這個是1.1T 是1.1的升級版

xinxingezi · 發表于 2017-11-22 10:07

hao501802766 發表于 2017-11-22 10:00
http://m.81jnr2m.cn/jc/article/17006-1.html
中興B860AV1.1-T2安裝教程

我就是按照這個教程跑的，跑出來的代碼，無法輸入指令，而且出來的指令明顯跟教程的不一樣
[ 1.1root@p200_2G:/ # [ 14.322965@0][ 5461/Threa] monitor: received netlink message:ztebw ok
[ 14.323765@0][ 5461/Threa] monitor:reply

xinxingezi · 發表于 2017-11-22 10:07

hao501802766 發表于 2017-11-22 10:00
http://m.81jnr2m.cn/jc/article/17006-1.html
中興B860AV1.1-T2安裝教程

我就是按照這個教程跑的，跑出來的代碼，無法輸入指令，而且出來的指令明顯跟教程的不一樣
[ 1.1root@p200_2G:/ # [ 14.322965@0][ 5461/Threa] monitor: received netlink message:ztebw ok
[ 14.323765@0][ 5461/Threa] monitor:reply

zxyyabc123 · 發表于 2017-11-24 22:24

同樣的問題有高手解決嗎？

qch1205 · 發表于 2017-11-25 17:46

同樣的問題有高手解決嗎？

hzzzzzp · 發表于 2017-12-2 01:57

同上

› 運營商IPTV / 有線電視 / 廣電機頂盒 › 中興機頂盒

中興機頂盒B8601.1T TTL后跑碼無法輸入指令 ...

中興機頂盒B8601.1T TTL后跑碼無法輸入指令

相關帖子