完美星空S2機頂盒里SYSTEM文件被刪變磚求救

xsj123 · 發表于 2016-12-21 14:28

  我的完美星空S2機頂盒里SYSTEM文件被刪變磚，按遙控器無反應，開機黑屏，用TTL線+SecureCRT文件傳輸模式傳固件或SYSTEM文件出錯，傳不進機頂盒里，只要將SYSTEM這個文件傳到里面就可成功。請哪位高手幫解答一下。機頂盒讀開機為：EEEE I3000000032940xf300110303;77520EEEE I400000004294_M6_BL1_3431>2534313
device is 16bit ddr
wait pll-0x03 target is 0204 now it is 0x00000203

DDR clock is 516MHz with 1T mode

516M clk
DX0DLLCR:40000000
DX0DQTR:ffffffff
DX0DQSTR:3db04001
DX1DLLCR:40000000
DX1DQTR:ffffffff
DX1DQSTR:3db04001
DX2DLLCR:40000000
DX2DQTR:ffffffff
DX2DQSTR:3db05001
DX3DLLCR:40000000
DX3DQTR:ffffffff
DX3DQSTR:3db05001
Stage 00 Result 00000000
Stage 01 Result 00000000
Stage 02 Result 00000000
Stage 03 Result 00000000
HHH
Boot From SPI0x12345678
Boot from internal device 1st SPI

System Started
℉ㄕ澆訓00000-g3e9c579(m6_mbx_g32@jb42-0630) (Apr 08 2014 - 12:22:39)

aml_rtc_init
aml rtc init first time!
Clear HDMI KSV RAM
DRAM:  1 GiB
relocation Offset is: 105e8000
NAND:  Amlogic nand flash uboot driver, Version U1.06.017 (c) 2010 Amlogic Inc.
SPI BOOT : continue i 0
No NAND device found!!!
NAND device id: ad d7 94 91 60 44
aml_chip->hynix_new_nand_type =: 4
NAND device: Manufacturer ID: 0xad, Chip ID: 0xad (Hynix C revision 20nm NAND 4GiB H27UBG8T2C)
1 NAND chips detected
#####aml_nand_init, with RB pins and chip->chip_delay:20
bus_cycle=5, bus_timing=6, start_cycle=6, end_cycle=7,system=5.0ns
oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH40_1K_MODE
aml_chip->oob_fill_cnt =64,aml_chip->oob_size =640,bch_bytes =70
multi plane error for selected plane mode: NAND_TWO_PLANE_MODE force plane to : NAND_SINGLE_PLANE_MODE
aml_nand_init:oobmul =1,chip->ecc.layout->oobfree[0].length=16,aml_chip->oob_size=640
aml_nand_get_read_default_value_hynix 980 get default reg value at blk:0, page:7
aml nand env valid addr: 410000 ,status =0
NAND bbt detect factory Bad block at ff800000
key start_blk=2039,end_blk=2047,aml_nand_key_init:684
aml nand key valid addr: ff000000
aml nand key valid addr: ff200000
aml nand key valid addr: ff400000
CONFIG_KEYSIZE=0x10000; KEYSIZE=0xfffc; bbt=0x1330; default_keyironment_size=0xeccc
i=0,register --- nand_key
NAND bbt detect factory Bad block at 57c00000
NAND bbt detect factory Bad block at 57e00000
NAND bbt detect factory Bad block at 68800000
NAND bbt detect factory Bad block at 68a00000
NAND bbt detect factory Bad block at 6f400000
NAND bbt detect factory Bad block at 6f600000
Creating 8 MTD partitions on "nandnormal":
0x000000c00000-0x000001400000 : "logo"
0x000001400000-0x000001c00000 : "aml_logo"
0x000001c00000-0x000002400000 : "recovery"
0x000002400000-0x000002c00000 : "boot"
0x000002c00000-0x000042c00000 : "system"
0x000042c00000-0x000063000000 : "cache"
NAND bbt detect factory Bad block at 57c00000
NAND bbt detect factory Bad block at 57e00000
0x000063000000-0x000073800000 : "backup"
NAND bbt detect factory Bad block at 68800000
NAND bbt detect factory Bad block at 68a00000
NAND bbt detect factory Bad block at 6f400000
NAND bbt detect factory Bad block at 6f600000
0x000073800000-0x0000fee00000 : "data"
NAND bbt detect factory Bad block at 7ec00000
NAND bbt detect factory Bad block at 7ee00000
NAND bbt detect factory Bad block at 80800000
NAND bbt detect factory Bad block at 80a00000
NAND bbt detect factory Bad block at a3800000
NAND bbt detect factory Bad block at a3a00000
NAND bbt detect factory Bad block at b6c00000
NAND bbt detect factory Bad block at b6e00000
NAND bbt detect factory Bad block at e2800000
NAND bbt detect factory Bad block at e2a00000
NAND bbt detect factory Bad block at fac00000
NAND bbt detect factory Bad block at fae00000
nandnormal initialized ok
detect mx chiprevD :1 and nand_type: 4
nand_curr_device =1
MMC: SDIO Port B: 0, SDIO Port C: 1
SPI BOOT,spi_env_relocate_spec : env_relocate_spec 53
SF: Unsupported manufacturer c2
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
register usb cfg[0] = 9fe82948
Net: current factory:<NULL>
SARADC open channel(6).
SARADC channel(6) is 0x17b.
set factory eth 101G phy..
Meson_Ethernet
init suspend firmware done. (ret:0)
detect_storage
nand exist return 0
setenv storage nand
reboot_mode=charging
ir init
switch_boot_mode
suspend_status_current2=0
current factory:<NULL>
SARADC open channel(6).
SARADC channel(6) is 0x13f.
str_getval = 0x13f,factorycode = 319
set factory:2
Saving Environment to SPI Flash...
SPI BOOT,spi_saveenv : saveenv 93
Environment SPI flash not initialized
Hit Enter key to stop autoboot:  0
Saving Environment to SPI Flash...
SPI BOOT,spi_saveenv : saveenv 93
Environment SPI flash not initialized
compatible nand
Booting from nand ...

NAND read: logo whole chip
8388608 bytes read: OK
wrong pack img!
cp - memory copy

Usage:
cp [.b, .w, .l] source target count

NAND read: boot offset 0x0, size 0x600000
6291456 bytes read: OK
pre-clear hdmi ram
hdcp get form storage medium: nand
name=nand_key nand_key
read:addr:0xff000000,phy_blk_addr:2040,phy_page_addr:0,aml_nand_get_key:125
device:nand, init key ok!!
don't found keyname,uboot_key_read:1502
prefetch hdcp keys from nand failed
Wrong Image Format for bootm command
ERROR: can't get kernel image!
enter recovery

NAND read: logo whole chip
8388608 bytes read: OK
wrong pack img!
cp - memory copy

Usage:
cp [.b, .w, .l] source target count

NAND read: recovery offset 0x0, size 0x600000
6291456 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
compatible nand
Booting from nand ...

NAND read: logo whole chip
8388608 bytes read: OK
wrong pack img!
cp - memory copy

Usage:
cp [.b, .w, .l] source target count

NAND read: boot offset 0x0, size 0x600000
6291456 bytes read: OK
pre-clear hdmi ram
hdcp get form storage medium: nand
don't found keyname,uboot_key_read:1502
prefetch hdcp keys from nand failed
Wrong Image Format for bootm command
ERROR: can't get kernel image!
enter recovery

NAND read: logo whole chip
8388608 bytes read: OK
wrong pack img!
cp - memory copy

Usage:
cp [.b, .w, .l] source target count

NAND read: recovery offset 0x0, size 0x600000
6291456 bytes read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
m6_mbx_g32# 用什么方法命令激活SD卡里的刷機固件進行刷機，按機內的短路點中間祿燈長亮就是不刷。原先按遙控器菜單鍵開機就可執行刷機，可無SYSTEM這個文件后遙控器不能用了。誰幫下我，謝謝了。

frozenwind717 · 發表于 2016-12-21 20:05

看這個http://m.81jnr2m.cn/tv-489233-1-1.html

xsj123 · 發表于 2016-12-22 08:52

frozenwind717 發表于 2016-12-21 20:05
看這個http://m.81jnr2m.cn/tv-489233-1-1.html

謝謝您能關注我，你發的完美星空S2刷第三方ROM圖文教程【附固件】，之前看過，用其它類似固件實驗沒成功，方法和步驟與你相同。主要就是第6第7步，短路那兩點祿燈亮了，它也不閃也不滅，屏幕也不出現那幾項選擇項，所以無法調用SD卡的刷機程序。這里我想請求一下您：選擇“apply update from EXT”這界面不出是什么情況，它發至機頂盒里被調用顯示在屏幕上，還是在燒錄好的SD卡的文件里，如果是這樣您的方法我看能行，現想試一下，還不知固件下載密碼，也不知您能否再次幫我，多謝。

frozenwind717 · 發表于 2016-12-22 16:31

回復帖子就有密碼了啊

frozenwind717 · 發表于 2016-12-22 16:31

密碼：zrcu

xsj123 · 發表于 2016-12-22 18:14

我試過沒好使，那我也要謝謝了。我又看了其它教程用雙公頭USB線連接完美星空S2機頂盒和電腦連接，電腦開始發現新硬件但驅動按不上。到設備管理器發現一個其它設備帶感嘆號，也就是驅動按不上，網上又下不著，又郁悶了，需要的驅動是M6-CHIP.這個M6-CHIP是什么文件，誰有，特請幫忙。

newlyyym · 發表于 2017-4-10 23:56

LZ搞定沒有？請教一下，機內的短路點是哪個元器件的哪兩個點，多謝了

aniuniu · 發表于 2017-10-6 20:13

我變磚又重新涮好了！開機紅燈和綠燈一起亮，紅燈滅馬上短接8腳25L80的56腳……

longya · 發表于 2018-8-23 10:53

aniuniu 發表于 2017-10-6 20:13
我變磚又重新涮好了！開機紅燈和綠燈一起亮，紅燈滅馬上短接8腳25L80的56腳…… ...

你好，請問你的盒子變磚，是完美星空s2嗎？需要短接兩次嗎？第二次怎么短接的能給個圖片嗎，因?yàn)榭床欢?6腳什么的

› 你問我答 / 玩機教程 / 固件 › ZNDS刷機/救磚

完美星空S2機頂盒里SYSTEM文件被刪變磚求救 ...

完美星空S2機頂盒里SYSTEM文件被刪變磚求救

相關帖子