|
|
本帖最后由 ygds 于 2018-3-31 15:27 編輯
河北聯通烽火HG680-R 用TTL線破解成功了，手賤百度ROOT，卡在logo，機器通電PUTTY跑亂碼停止無法輸入，主板SW6短路無反應，試圖短接flash無從下手，求助高手賜解決方法。
捕獲.PNG (371.56 KB, 下載次數: 37)
下載附件
保存到相冊
卡在開機第一屏
2018-3-29 09:44 上傳
AC_ON
MIU0_DQS-OK
MIU01_U
Relocation Offset is: 011d7000
[AT][MB][start ub][393]
U-Boot 2011.06 (Sep 12 2016 - 11:02:30)
[MIU INFO] miu opencreate instance at 559e9418 with private size 80 bytes at 559e9460
create instance at 559e94b8 with private size 52 bytes at 559e9500
uboot held at [557ddf60~56b00000],size=013220a0
CPU : Clippers
Board: BD_MST207C_D01A_S_CLIPPERS
DRAM: 875 MiB
Now running in RAM - U-Boot at: 55c00000
eMMC: HS200 200MHz
eMMC 3.63 GB [747FF8h]
In: serial
Out: serial
Err: serial
Net: No ethernet found.
MAC: 0x10: 0x77: 0xb0: 0xae:0x79: 0xc0
msIR_Initialize
In HAL_AUDIO_SetDspBaseAddr, line(4350), u8Index(0x0), u32Bin_Base_Address(0x0), u32Mad_Base_Buffer_Adr(0x37bb0000)
In HAL_AUDIO_SetDspBaseAddr, line(4350), u8Index(0x1), u32Bin_Base_Address(0x0), u32Mad_Base_Buffer_Adr(0x37930000)
In HAL_AUDIO_SetDspBaseAddr, line(4350), u8Index(0x2), u32Bin_Base_Address(0x0), u32Mad_Base_Buffer_Adr(0x37130000)
[======= initialize DEC-R2[0] SHM =======]
[======= initialize DEC-R2[1] SHM =======]
audio DSP_SE LoadCode success..[[utopia]] === HAL_MAD_SetDecCmd 0 fail===
DEC System code download finished!
[CPU INFO] cpu opencreate instance at 559f99c0 with private size 44 bytes at 559f9a08
CPUIoctl - MDrv_CMD_CPU_QueryClock
[UTOPIA INFO] close moduleNames[38]: MODULE_CPU
[AT][MBoot][Driver Init][766]
[AT][MB][do_bootm][1072]
Check USB port[0]:
Host type:2
scanning bus for devices...
[USB] interface[0] conf:1 value ff:
1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
FAIL : can not init usb 0!!
[AT][MB][do_bootm][2141]
MPOOL size : 0x200000
Changelist: 24543697
============= set bootargs ===============
Hit any key to stop autoboot: 0
AC on
fore uup IRKey [0xff]
create instance at 559f9cc0 with private size 256 bytes at 559f9d08
MDrv_PNL_Init u32PnlRiuBaseAddr = 1f200000
MDrv_PNL_Init u32PMRiuBaseAddr = 1f000000
PNL:[MDrv_PNL_SetPanelType][613]
[_MDrv_PNL_Init_LPLL][323]pstPanelInitData->u16Width=1920, pstPanelInitData->u16Height=1080
[_MDrv_PNL_Init_LPLL][325]u16HTotal=2200,u16VTotal=1125,pstPanelInitData->u16HTotal=2200,pstPanelInitData->u16VTotal=1125, u16DefaultVFreq=600
[_MDrv_PNL_Init_Output_Dclk][369]pstPanelInitData->u16Width=1920, pstPanelInitData->u16Height=1080
[_MDrv_PNL_Init_Output_Dclk][371]u16HTotal=2200,u16VTotal=1125,pstPanelInitData->u16HTotal=2200,pstPanelInitData->u16VTotal=1125, u16DefaultVFreq=600
PNL:CalculateLPLLSETbyDClk u32KHz = 1485000000, u64DefaultLdHz = 1485000000
PNL:CalculateLPLLSETbyDClk u32LpllSet = 3531df
[MApi_XC_MLG_GetStatus, 1603]No instance existed, please get an instance by calling MApi_XC_Init() first
msHdmitx_Disp_Init
create instance at 559f9e10 with private size 1720 bytes at 559f9e58
[XC,Version]
no need to patchcreate instance at 559faa58 with private size 80 bytes at 559faaa0
Rx Support HDMI mode!
shift 0 pixels in NTSC mode
Create Dolby single part name task failed!![Hal_VE_Set_PreHSD][1817] ERROR!!! HVSD H input = 0, HVSD H output = 720
[Hal_VE_Set_PreVSD][1991] ERROR!!! HVSD V input = 0, HVSD V output = 480
[Hal_VE_EnableDI][2099] bEnable = 0, bIsDNR2VE = 0
mmc change mount : userdata
Size of file "local/boot0.jpg" from mmc device 0 partition userdata: -1 bytes
mmc change mount : tvconfig
Size of file "/boot0.jpg" from mmc device 0 partition tvconfig: 1743469 bytes
Loading file "/boot0.jpg" at offset 0x0 from mmc device 0 partition tvconfig
1743469 bytes read
create instance at 55a0c2a0 with private size 304 bytes at 55a0c2e8
[AT][MB][JPD Decode][3058]
[UTOPIA INFO] close moduleNames[35]: MODULE_NJPEG_EX
create instance at 55a0c2a0 with private size 132280 bytes at 55a2c990
[GOP INFO] gop opencreate instance at 559faaf8 with private size 6908 bytes at 559fab40
[AT][MB][Show Logo][3110]
Unknown command 'uart_rx' - try 'help'
[ERROR] _RawData_Authentication:1532: Auth boot SUCCESS
[ERROR] Secure_doAuthentication:94: Error: Authentication Fail!!
[ERROR] _RawData_Authentication:1516: Auth system FAIL
mmc change mount : userdata
Size of file "local/boot_error.jpg" from mmc device 0 partition userdata: -1 bytes
mmc change mount : tvconfig
Size of file "/boot_error.jpg" from mmc device 0 partition tvconfig: -1 bytes
Loading file "/boot_error.jpg" at offset 0x0 from mmc device 0 partition tvconfig
** File not found /boot_error.jpg **
[ERROR] vfs_read:531: ext4load mmc fail
create instance at 55a0e388 with private size 304 bytes at 55a0e3d0
[AT][MB][JPD Decode][5348]
[UTOPIA INFO] close moduleNames[35]: MODULE_NJPEG_EX
[AT][MB][Show Logo][5376]
跑碼到此無法輸入，請高手指點。
|
上一篇： 新人報到下一篇： 后續問題又來了！
|
網站導航
發表于 2018-3-29 09:46
收藏
淘帖
頂一個
踩
提升卡
置頂卡
變色卡
千斤頂
樓主
znds.com 