南京移動CM101s刷機變磚，求幫助，謝謝！

張煒_Yv7lz · 發表于 2017-10-9 23:38

【1】盒子品牌型號：南京移動CM101s
【2】盒子目前存在情況/需要什么技術支持：自己刷機變磚，目前putty啟動如下。求技術支持或重新刷機，謝謝！@hao501802766

Bootrom start
Boot from eMMC
Starting fastboot ...

System startup
DDRS
Reg Version:  v1.1.0
Reg Time:    2016/2/25  9:23:54
Reg Name:    hi3798mdmo1g_hi3798mv100_ddr3_1gbyte_16bitx2_4layers_emmc.reg

Jump to DDR

Fastboot 3.3.0-00692-g8276f4e-dirty (root@HW-TV-S3) (Jun 30 2016 - 02:07:27)

Fastboot:    Version 3.3.0
Build Date: Jun 30 2016, 02:08:32
CPU:          Hi3798Mv100
Boot Media: eMMC
DDR Size:    1GB

Check nand flash controller v610. found
Special NAND id table Version 1.36
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found!!!

MMC/SD controller initialization.
MMC/SD Card:
MID:       0x11
Read Block:  512 Bytes
Write Block: 512 Bytes
Chip Size: 7456M Bytes (High Capacity)
Name:       "008G3"
Chip Type: MMC
Version:    4.0
Speed:    52000000Hz
Bus Width: 8bit
Boot Addr: 0 Bytes

*** Warning - bad CRC or eMMC, using default environment

Boot Env on eMMC
Env Offset:       0x00100000
Env Size:          0x00010000
Env Range:          0x00010000
HI_OTP_LockIdWord,327: ID_WORD have already been locked

SDK Version: HiSTBAndroidV600R001C00SPC063_v2016022921

get key value  0x0
HI_Flash_Read Ret= 3072
HI_Flash_Read Ret= 3072
HI_Flash_Read Ret= 10485760
HI_Flash_Read Ret= 10485760
******** boot from kernel...********
bootargs = HI_Flash_Read Ret= 512
HI_Flash_Read Ret= 512
Stb mac is : [00:00:00:00:00:00]
The mac is not a valid mac, use default mac.

Reserve Memory
Start Addr:       0x3FFFE000
Bound Addr:       0x8D3D000
Free  Addr:       0x3F875000
Alloc Block:  Addr       Size
               0x3FBFD000    4194304
               0x3F8FC000    3145728
               0x3F87B000    524288
               0x3F878000    8192
               0x3F875000    8192

Press Ctrl+C to stop autoboot

kernel  @ 0 (0 bytes)
ramdisk @ 0 (0 bytes)
page size @ 0 bytes
initrd rd_start = 0,rd_end = 0
Wrong Image Format !!!
fastboot#

茄子燉排骨 · 發表于 2017-10-10 10:21

@hao501802766

hao501802766 · 發表于 2017-10-10 10:38

得重新燒錄系統文件進去或者強刷第三方固件才可以解決

張煒_Yv7lz · 發表于 2017-10-11 22:06

hao501802766 發表于 2017-10-10 10:38
得重新燒錄系統文件進去或者強刷第三方固件才可以解決

嗯，可以共享一下刷機鏡像和操作指導嗎？我有hitool和TTL線。謝謝！

hao501802766 · 發表于 2017-10-12 10:53

張煒_Yv7lz 發表于 2017-10-11 22:06
嗯，可以共享一下刷機鏡像和操作指導嗎？我有hitool和TTL線。謝謝！

可以加我好友 501802766 備注ZNDS論壇 cm101s 燒錄文件

› 你問我答 / 玩機教程 / 固件 › ZNDS刷機/救磚