求救磚 付費 江蘇移動創維E900V21C

jiyong123

         @hao501802766         
        前兩天剛剛把刷機心得（2017年12月 江蘇移動創維E900V21C刷機成功）和大家分享了。由于徹底關機后再開機，WIFI需要手動連接，覺得是固件版本的問題，昨晚重新試了《樂天20170828版-卡刷包》，刷完盒子重啟，盒子就再也沒亮起來了，電視直接什么圖像都沒有。
     換了2臺電腦，3條USB線，   2條TTL線（CH341線，PL2303線）    

故障現象：
1、通電后，主板上PWR主電源燈亮一下綠燈就變紅了；LAN網口燈一直紅燈；IR遙控?zé)粢恢笔?/font>熄滅狀態。
2、刷機軟件USB_Burning_Tool，一直發現不了盒子，且反復開關都不識別。
3、TTL跑到一半就卡住了，怎么回車都沒反應，試了很多次。
Starting kernel ...
uboot time: 2041271 us
[    0.000000@0] Initializing cgroup subsys cpu
[    0.000000@0] Initializing cgroup subsys cpuacct
[    0.000000@0] Linux version 3.14.29-svn125577 (chenshouhui@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Sat Mar 18 22:16:52 HKT 2017
[    0.000000@0] CPU: armv71 Processor [410fd034] revision 4
[    0.000000@0] bootconsole [earlycon0] enabled
INFO:    HDCP22 key read fail!
INFO:    p1d 0
INFO:    pd1 0

4、TTL完整信息在2樓

jiyong123

GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 101949

BL2 Built : 18:58:24, Oct 25 2016.
gxl gc9db010 - xiaobo.gu@droid05

set vcck to 1080 mv
set vddee to 1050 mv
Board ID = 2, adc=153
CPU clk: 1200MHz
2layers board, use ddr_set[0]
DDR chl: Rank0+1 @ 720MHz - FAIL
DDR chl: Rank0 @ 720MHz - PASS
DQS-corr enabled
DDR scramble enabled
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x00007400
Load bl301 from eMMC, src: 0x00018200, des: 0x01200000, size: 0x00002000
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a6200
NOTICE:  BL3-1: v1.0(debug):959fdf0
NOTICE:  BL3-1: Built : 15:01:44, Dec 29 2016
aml log : bl31 normal boot !
[Image: gxl_v1.1.3086-872dec0 2016-09-21 21:56:30 xiaobo.gu@droid05]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: ef be ad de d f0 ad ba ef be ad de not ES chip
efuse init ops = c2
efuse init hdcp = c, cf9=7
[0.414842 Inits done]
seINFcOu:r e   t aBsLk3 -s1t:a rItn!it
ializing runhtiigmhe  tsaesvices
WARNING: No OPTEE provided by BL2 boot loader
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address = 0x1000000
INFO:    BL3-1: Next image spsr = 0x3c9


U-Boot 2015.01-svn125577 (Mar 18 2017 - 21:47:22)

DRAM:  1 GiB
Relocation Offset is: 36ecf000
gpio: pin GPIODV_24 (gpio 43) value is 0
gpio: pin GPIOAO_3 (gpio 103) value is 1
mwm 0xc8837004:[0x   aa203] with [0x   ea203] ok
mwm 0xc883700c:[0x 3e3b744] with [0x 3e3b764] ok
mwm 0xc8837010:[0x   c0101] with [0x   c8101] ok
mwm 0xc8837010:[0x   c8101] with [0x  128101] ok
register usb cfg[0][1] = 0000000037f63db0
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC:   aml_priv->desc_buf = 0x0000000033ebfdb0
aml_priv->desc_buf = 0x0000000033ec20d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
[mmc_startup] mmc refix success
[mmc_init] mmc init success
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In:    serial
Out:   serial
Err:   serial
board id is : 2
hpd_state=1
[720p50hz] is invalid for cvbs.
set hdmitx VIC = 19
config HPLL = 2972
HPLL: 0xc000027b
config HPLL done
j = 2  vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 19
enc_vpu_bridge_reset[1189]
rx version is 1.4 or below  div=10
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
dwmac.c9410000
Error: dwmac.c9410000 address not set.

wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode=cold_boot
[CANVAS]canvas init
[CANVAS]addr=0x3d800000 width=5760, height=2160
[OSD]ERR: 24 bit/pixel mode, but BMP has 16 bit/pixel
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
amlkey_issecure() 138: ret 1
amlkey_size() 162: ret 1
[KM]Error:f[key_unify_read]L301:key[mac] not programed yet
[KM]Error:f[do_sec_keyunify]L682:mac key read fail
don't use random mac produce in uboot
IR init done!
gpio: pin GPIOH_6 (gpio 55) value is 1
Hit any key to stop autoboot:  0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f44bc0
copy done
      Single dtb detected
load dtb from 0x1000000 ......
   Uncompressing Kernel Image ... OK
   kernel loaded at 0x01080000, end = 0x02033200
   Loading Ramdisk to 33c36000, end 33ebca00 ... OK
   Loading Device Tree to 000000001fff3000, end 000000001ffff3a1 ... OK

Starting kernel ...

uboot time: 2041271 us
[    0.000000@0] Initializing cgroup subsys cpu
[    0.000000@0] Initializing cgroup subsys cpuacct
[    0.000000@0] Linux version 3.14.29-svn125577 (chenshouhui@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Sat Mar 18 22:16:52 HKT 2017
[    0.000000@0] CPU: armv71 Processor [410fd034] revision 4
[    0.000000@0] bootconsole [earlycon0] enabled
INFO:    HDCP22 key read fail!
INFO:    p1d 0
INFO:    pd1 0

hao501802766

jiyong123 發表于 2017-12-21 12:09
GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 101949

用雙頭USB 重刷這個包：http://m.81jnr2m.cn/rom/20132.html

jiyong123

hao501802766 發表于 2017-12-21 12:39
用雙頭USB 重刷這個包：http://m.81jnr2m.cn/rom/20132.html

雙頭的線換了好幾條了
刷機軟件一直識別不到盒子

hao501802766

jiyong123 發表于 2017-12-21 12:44
雙頭的線換了好幾條了
刷機軟件一直識別不到盒子

盒子接通電源開機 然后馬上插入U(xiǎn)SB 應該可以  我是這樣刷機操作基本都OK

jiyong123

我都是關機，插上USB，再插電源，不行！
按你的方法 連續測試了20次 還是不行！
軟件發現不了盒子

hao501802766

那我也沒好的辦法了  要么就選擇寄過來 我試試看  當然也不保證一定能弄好

jiyong123

hao501802766 發表于 2017-12-21 13:55
那我也沒好的辦法了  要么就選擇寄過來 我試試看  當然也不保證一定能弄好 ...

可以的 江浙滬范圍 發給你們很方便的

jiyong123

hao501802766 發表于 2017-12-21 13:55
那我也沒好的辦法了  要么就選擇寄過來 我試試看  當然也不保證一定能弄好 ...

地址已收到，沒權限發短消息。這里回復，明天發快遞出去

jiyong123

@hao501802766      
快遞已發 申通402886040185