ZTE B860A 有線(itv dhcp) + wifi(互聯網) 雙線自動切換腳本

NadOo

ZTE B860A 有線(itv dhcp) + wifi(互聯網) 雙線自動切換腳本


本腳本適合：1. 中興B860A；
2. 當?shù)豬tv采用dhcp方式連接；
3. 機頂盒支持有線和wifi同時保持連接(同時連接時，有線和無線都有IP，但只有一個生效)；


如果你是pppoe方式連接itv，參考：http://m.81jnr2m.cn/tv-579100-1-1.html

~~~~~
周末研究了一下，結合網上已有資源修改，已實現雙線自動切換，成都電信B860A上測試通過，分享出來供大家參考：

1. 盒子有線連接iTV，無線連接互聯網wifi；通過ttl或adb、telnet、ssh等方式，獲取root身份的shell，詳情參考論壇其它帖子；
2. 安裝當貝市場或其它桌面程序，可通過U盤的方式，將apk文件拷貝之/data/app；

1. #四川電信B860A v1.0版本，U盤掛載于/storage/external_storage/sda4

復制代碼

3. 以讀寫權限重新掛載/system目錄，并創建netchange.sh
重新掛載目錄：

1. mount -o rw,remount /system

復制代碼

創建netchange.sh并打開vi編輯器：

1. vi /system/bin/netchange.sh

復制代碼

編輯netchange.sh，先敲鍵盤i鍵，然后粘貼如下腳本：

1. #!/system/bin/sh
   
2. 
   
3. # ZTE B860A netchange.sh
   
4. # eth0: iTV cable, wlan0: Wifi internet
   
5. # Author: http://github.com/nadoo
   
6. # Date: 2016-10-24
   
7. 
   
8. # mount -o rw,remount /system
   
9. # vi /system/bin/netchange.sh
   
10. # chmod 0755 /system/bin/netchange.sh
    
11. # echo "/system/bin/netchange.sh &" >> /system/bin/init.zte.post_boot.sh
    
12. 
    
13. # disable upgrade
    
14. pm block com.ztestb.upgrade
    
15. 
    
16. # wait for wlan or itv link up
    
17. while [ "$(getprop net.zte.eth.netstate)" != "CONNECTED" ] && [ "$(getprop net.zte.wifi.netstate)" != "CONNECTED" ]
    
18. do
    
19.         sleep 1
    
20. done
    
21. 
    
22. 
    
23. 
    
24. # 0:web 1:itv
    
25. itv=1
    
26. 
    
27. while [ 1 ]
    
28. do
    
29.         # check whether itv is current window
    
30.         check_app=$( dumpsys window windows | grep -E 'mCurrentFocus|mFocusedApp' | grep -E com.zte.browser | busybox wc -l )
    
31. 
    
32.         # gateway and dns
    
33.         web_if="wlan0"
    
34.         web_gw=$(getprop dhcp.wlan0.gateway)
    
35.         web_dns=$(getprop dhcp.wlan0.dns1)
    
36. 
    
37.         itv_if="eth0"
    
38.         itv_gw=$(getprop dhcp.eth0.gateway)
    
39.         itv_dns=$(getprop dhcp.eth0.dns1)
    
40. 
    
41.         if [ $check_app != 0 ] && [ $itv != 1 ]; then
    
42.                 echo "=itv started..."
    
43.                 if [ $itv_gw = "" ]; then
    
44.                         echo "=please connect itv..."
    
45.                 else
    
46.                         itv=1
    
47.                         ip route del
    
48.                         ip route del
    
49.                         ip route add default via $itv_gw
    
50.                         ip route add $itv_dns via $itv_gw
    
51.                         ndc resolver flushdefaultif
    
52.                         ndc resolver setifdns $itv_if "" $itv_dns
    
53.                         ndc resolver setdefaultif $itv_if
    
54.                         sleep 1
    
55.                         echo "=switched to $itv_if..."
    
56.                         echo "=gateway:$itv_gw dns:$itv_dns"
    
57.                 fi
    
58.         elif [ $check_app = 0 ] && [ $itv = 1 ]; then
    
59.                 echo "=itv stopped..."
    
60.                 if [ $web_gw = "" ]; then
    
61.                         echo "=please connect wifi..."
    
62.                 else
    
63.                         itv=0
    
64.                         ip route del
    
65.                         ip route del
    
66.                         ip route add default via $web_gw
    
67.                         ip route add $itv_dns via $itv_gw
    
68.                         ndc resolver flushdefaultif
    
69.                         ndc resolver setifdns $web_if "" $web_dns
    
70.                         ndc resolver setdefaultif $web_if
    
71.                         sleep 1
    
72.                         echo "=switched to $web_if..."
    
73.                         echo "=gateway:$web_gw dns:$web_dns"
    
74.                 fi
    
75.         fi
    
76.       
    
77.         sleep 1
    
78.         
    
79. done

復制代碼

保存腳本并退出，接連按下：ESC，:wq，回車

為腳本增加可執行權限：

1. chmod 0755 /system/bin/netchange.sh

復制代碼

使腳本隨機自啟動：
在/system/bin/init.zte.post_boot.sh文件最后一行，加入：

1. /system/bin/netchange.sh &

復制代碼

4. 重新啟動盒子，按下遙控器"主頁"或"應用"鍵，即可進入桌面Launcher，將當貝桌面設置為默認桌面，然后將系統自帶應用的"互動電視"放置到桌面首頁；

之后進入"互動電視"，則自動切換到有線，退出"互動電視"，則自動切換到wifi(互聯網)上網，第三方apk可正常使用；
其它：解除四川電信禁止安裝apk的限制，方法(其它地區如果沒有限制apk安裝，則應該不需要做這一步)：

1. 用機頂盒配置工具StbCfgTool，連接盒子成功后，先在基本配置欄讀取配置，再在特征配置-國家-省份-運營商處修改為：中國通用市場！然后在基本配置欄寫入配置，重起盒子即可（如果報錯不能寫入，將此欄MLD版本號改為1就可以了?。?/ol>

復制代碼

關于解除四川電信安裝apk的限制，可以參考byron_zhj的詳細操作說明：
http://m.81jnr2m.cn/tv-567820-1-1.html

NadOo

cashwl 發表于 2016-10-31 04:21
經760EV3測試無效

我已經改用單線多vlan方式了，有線比無線快多了，腳本差不多.

因?yàn)楦鞯丨h(huán)境不一樣，你可以：

1. 連接iTV的網線，斷開wifi，分別執行以下命令，貼出結果：
ip addr
ip route
getprop | grep dhcp
getprop | grep eth
getprop | grep ppp

2. 連接iTV的網線，同時連接wifi，分別執行以下命令，貼出結果：
ip addr
ip route
getprop | grep dhcp
getprop | grep eth
getprop | grep ppp

xzw007

doityou 發表于 2016-10-21 12:47
我的iptv是pppoe的，可能問題出在這，可是我不會改。

130|root@n200:/ # ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST> mtu 1452 qdisc pfifo_fast state DOWN qlen 1000
    link/ether 74:97:81:29:d5:94 brd ff:ff:ff:ff:ff:ff
3: tunl0: <NOARP> mtu 0 qdisc noop state DOWN
    link/ipip 0.0.0.0 brd 0.0.0.0
4: sit0: <NOARP> mtu 1480 qdisc noop state DOWN
    link/sit 0.0.0.0 brd 0.0.0.0
5: ip6tnl0: <NOARP> mtu 1452 qdisc noop state DOWN
    link/tunnel6 :: brd ::
9: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1452 qdisc mq state UP qlen 1000
    link/ether 34:c3:d2:4c:2b:55 brd ff:ff:ff:ff:ff:ff
    inet 192.168.10.103/24 brd 192.168.10.255 scope global wlan0
       valid_lft forever preferred_lft forever
    inet6 fe80::36c3:d2ff:fe4c:2b55/64 scope link
       valid_lft forever preferred_lft forever
10: p2p0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1452 qdisc mq state DOWN qlen 1000
    link/ether 36:c3:d2:4c:2b:55 brd ff:ff:ff:ff:ff:ff
root@n200:/ # [  227.772291@0] init: sys_prop: permission denied uid:10023  gid:10023 name:persist.service.adb.enable
[  227.779870@0] init: sys_prop: permission denied uid:10023  gid:10023 name:service.adb.tcp.port
[  227.788215@0] init: sys_prop: Unable to start service ctl [adbd] uid:10023 gid:10023 pid:11530
[  237.828885@0] init: sys_prop: permission denied uid:10023  gid:10023 name:persist.service.adb.enable
[  237.836289@0] init: sys_prop: permission denied uid:10023  gid:10023 name:service.adb.tcp.port
[  237.844804@0] init: sys_prop: Unable to start service ctl [adbd] uid:10023 gid:10023 pid:11930
[  247.887340@0] init: sys_prop: permission denied uid:10023  gid:10023 name:persist.service.adb.enable
[  247.897042@0] init: sys_prop: permission denied uid:10023  gid:10023 name:service.adb.tcp.port
[  247.906297@0] init: sys_prop: Unable to start service ctl [adbd] uid:10023 gid:10023 pid:12326
QA9:A;SVN:74E;POC:17F;STS:0;BOOT:0;INIT:0;READ:0;CHECK:0;PASS:0;
no sdio debug board detected
TE : 1279059
BT : 11:31:49 Jun  2 2016
NO PMU:use DCDC
##### VDDEE voltage = 0x044c

CPU clock is 792MHz

BOARD type: 0x06
CPU type: M8M2
DDR info: 1GB(auto) @ 792MHz(1T)+Scramb EN
DDR channel: DDR 0 + DDR 1

DDR init use : 14682 us

HHH
Boot From SDIO C
0x0000008d
ucl decompress...pass
0x12345678
Boot from internal device 1st tSD/fSD on SDIO C

TE : 1519491

System Started


U-boot-svn61849(m8_k200_v1@) (Jun 02 2016 - 11:31:34)

clr h-ram
DRAM:  1 GiB
relocation Offset is: 2fe94000
show partition table:
part: 0, name :       conf, size : 400000
part: 1, name :       logo, size : 1000000
part: 2, name :   recovery, size : 1400000
part: 3, name :       misc, size : 400000
part: 4, name :       boot, size : 1400000
part: 5, name :      cache, size : 30000000
part: 6, name :     system, size : 30000000
part: 7, name :       data, size : 79000000
part: 8, name :           , size : 0   
part: 9, name :           , size : 0   
part: 10, name :           , size : 0   
part: 11, name :           , size : 0   
part: 12, name :           , size : 0   
part: 13, name :           , size : 0   
part: 14, name :           , size : 0   
part: 15, name :           , size : 0   
aml_card_type=0x200
MMC:   [mmc_register] add mmc dev_num=0, port=1, if_type=6
[mmc_register] add mmc dev_num=1, port=2, if_type=6
SDIO Port B: 0, SDIO Port C: 1
board_type 6
register usb cfg[0][1] = 3ff6bf40
register usb cfg[2][0] = 3ff6f838
enter emmc boot
Emmckey: Access range is illegal!
[mmc_init] SDIO Port C:1, if_type=6, initialized OK!
[mmc_get_partition_table] end of part_table, index 8.
Partition table get from SPL is :
        name                        offset              size              flag
===================================================================================
   0: bootloader                         0            400000                  0
   1: reserved                      800000           1000000                  0
   2: env                          1c00000            400000                  0
   3: conf                         2400000            400000                  1
   4: logo                         2c00000           1000000                  1
   5: recovery                     4000000           1400000                  1
   6: misc                         5800000            400000                  1
   7: boot                         6000000           1400000                  1
   8: cache                        7800000          30000000                  2
   9: system                      37c00000          30000000                  1
  10: data                        68000000          79000000                  4
mmc read lba=0x4000, blocks=0x1
mmc read lba=0x4001, blocks=0x1
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
i=0,register --- emmc_key
device_boot_flag=2
EMMC BOOT: not init nand
do not init nand : cause boot_device_flag without nand
MMC BOOT, emmc_env_relocate_spec : env_relocate_spec 74
set_storage_device_flag: store 2
vpu driver detect cpu type: m8m2
vpu clk_level = 7
set vpu clk: 364000000Hz, readback: 364000000Hz(0x700)
mode = 11  vic = 31
set HDMI vic: 31
config HPLL
config HPLL done
reconfig packet setting done
Err imgread(L129):Fmt unsupported!genFmt 0x0 != 0x3
Net:   Meson_Ethernet
init suspend firmware done. (ret:0)
cvbs trimming.1.v5: 0xa0, 0x0
hdcp init_hdcp_ram...
reboot_mode=charging
Hit Enter key to stop autoboot -- :  0
exit abortboot: 0
[Logo_disp]: ====== Logo_disp ======
[draw_logo]: before read_logo_data
[draw_logo]: draw_logo 1475
[draw_logo]: draw_logo 1477
[set_logoParam]: enter the set_logoParam
[set_logoParam]:  Id            FileName                Type            No      Addr                    Size
[set_logoParam]: before the get_logo_source PAL_LOGO_PICTURE
[set_logoParam]:  <0>           LogoPic(480i)           0               1      0x11000288               541225
[set_logoParam]:  <1>           LogoPic(576i)           0               2      0x110844b4               114717
[set_logoParam]:  <2>           LogoPic(720p)           0               3      0x110a04d4               47966
[set_logoParam]:  <3>           LogoPic(1080i_p)        0               2      0x110ac034               90410
[draw_logo]: draw_logo 1520
before the  decompressToRGB
Start to decode the LOGO jpeg ...
[decompressToRGB]: before the decompress_jpeg_rgb
[decompressToRGB]: Call decompress_pic_rgb565(id=3,addr=110ac034,size=90410,maxw=1920,maxh=1080,Bpp=3) ...
[decompressToRGB]: after the decompress_jpeg_rgb
[draw_logo]: Success in decoding LOGO src file: (w=1920,h=1080,Bpp=3,data=0x3f2b0aa8)
[deinit_Logo]: all LOGO's resource (Exc. logoThread) are released
Logo_disp ret: 0
not found mac in efuse
do_bootsys to boot NORM
head magic=55667788
cmdT = mmc read boot 11ffffa0 0 704e00;bootm 12000000
hdcp init_hdcp_ram...
## ANDROID Format IMAGE
## Booting kernel from Legacy Image at 12000000 ...
   Image Name:   Linux-3.10.33
   Image Type:   ARM Linux Kernel Image (lzo compressed)
   Data Size:    6265692 Bytes = 6 MiB
   Load Address: 00208000
   Entry Point:  00208000
   Verifying Checksum ... OK
    Ramdisk start addr = 0x125fa800, len = 0xe2a7a
      Multi dtb tool version: v2 .
      Multi dtb detected, support 7 dtbs.
        aml_dt soc: m8m2 platform: n200c variant: sdio
        dtb 0 soc: m8m2   plat: n200   vari: 1G
        dtb 1 soc: m8m2   plat: n200   vari: 2gsdhc
        dtb 2 soc: m8m2   plat: n200   vari: 2gsdio
        dtb 3 soc: m8m2   plat: n200   vari: sdhc
        dtb 4 soc: m8m2   plat: n200   vari: sdio
        dtb 5 soc: m8m2   plat: n200c   vari: sdhc
        dtb 6 soc: m8m2   plat: n200c   vari: sdio
      Find match dtb: 6
    Flat device tree start addr = 0x126ff000, len = 0x5493 magic=0xedfe0dd0
   Uncompressing Kernel Image ... OK
uboot time: 3496746 us.
EFUSE machid is not set.
Using machid 0xf81 from environment
From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x50ec001
   Loading Ramdisk to 05009000, end 050eba7a ... OK
   Loading Device Tree to 05000000, end 05008492 ... OK

Starting kernel ...

[    0.146593@0] ram_console: failed to create proc entry
[    0.422709@0] aml_keys: version 0 can not be init c0af4ff0
[    0.814615@2] aml_keys: version 0 can not be init c0af4ff0
[    0.814671@2] aml_keys: version 0 can not be init c0af4ff0
[    0.857440@1] ###check hw reset function is already enabled here
[    0.982232@2] init: failed to [    1.864826@3] init: mount none to target failed
[    1.920828@3] init: mount none to target failed
[    1.925179@3] init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}'
[    1.927871@3] init: cannot expand '${ro.serialno}' while writing to '/sys/class/android_usb/android0/iSerial'
[    1.938182@3] init: mount adb to target failed
[    2.227246@3] aml_keys: version 0 can not be init c0af4ff0
[    2.274944@1] init: mount ext4 to target failed
[    2.287346@1] init: open /data/local/bootanimation.zip failed
[    2.293218@1] init: ## ProductID: strlen (32)!
[    2.293250@1] init: StbTypeID :(334)
[    2.299775@1] init: [DingQin] load_stbconfig_set_properties --> marketCode = 1, operatorsCode = 1init: myinit: company=, vcisvraddr =  vcisvrport = , bootdir = :
[ [    2.339035@1] init: cannot find '/sbin/cp7601.sh', disabling 'zte-7601-cp'
[    2.340957@1] init: cannot find '/system/bin/IptvServ', disabling 'IptvServ'
[    2.347504@1] init: cannot find '/system/bin/ys_service', disabling 'ys-service'
[    2.355133@1] init: cannot find '/system/bin/init.toltech.sh', disabling 'toltech_devices'
[    2.364366@1] init: cannot find '/system/bin/ztepropertyd', disabling 'ztepropertyd'
[    2.423907@1] init: cannot expand '${ro.usb.vendor.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/vendor_string'
[    2.431030@1] init: property 'ro.usb.product.string' doesn't exist while expanding '${ro.usb.product.string}'
[    2.440734@1] init: cannot expand '${ro.usb.product.string}' while writing to '/sys/class/android_usb/android0/f_mass_storage/product_string'
[    2.497772@1] init: property 'sys.powerctl' doesn't exist while expanding '${sys.powerctl}'
[    2.501213@1] init: powerctl: cannot expand '${sys.powerctl}'
[    2.506979@1] init: property 'sys.sysctl.extra_free_kbytes' doesn't exist while expanding '${sys.sysctl.extra_free_kbytes}'
[    2.518034@1] init: cannot expand '${sys.sysctl.extra_free_kbytes}' while writing to '/proc/sys/vm/extra_free_kbytes'
root@n200:/ # [    2.689255@0] ztebsp: set_display_mod->store_free_scale_axis 0 0 0 1279 719
[    2.690829@0] ztebsp: set_display_mod->store_window_axis 0 33 18 1885 1060
[    9.933159@1] ztebsp: system_server->store_window_axis 0 33 18 1885 1060
[   10.051588@0] ztebsp: system_server->set_vout_window osd0=>x:33 ,y:18,w:1920,h:1080
[   10.051588@0]  osd1=> x:33,y:18,w:18,h:18
[   11.877206@0] init: untracked pid 970 exited
[   11.895718@1] init: untracked pid 971 exited
[   13.141119@2] init: untracked pid 1187 exited
[   13.679442@2] init: cannot find '/system/bin/preinstall.sh', disabling 'preinstall'
[   13.845124@1] init: no such service 'wififix'
[   15.815505@0] init: untracked pid 1063 exited
[   17.208497@1] init: sys_prop: permission denied uid:10023  gid:10023 name:persist.service.adb.enable
[   17.217613@1] init: sys_prop: permission denied uid:10023  gid:10023 name:service.adb.tcp.port
[   17.235906@1] init: sys_prop: Unable to start service ctl [adbd] uid:10023 gid:10023 pid:1684
[   20.175452@2] init: untracked pid 1951 exited
[   22.856081@2] init: untracked pid 2345 exited
[   23.576411@2] init: untracked pid 2347 exited
[   27.370031@2] init: sys_prop: permission denied uid:10023  gid:10023 name:persist.service.adb.enable
[   27.381035@1] init: sys_prop: permission denied uid:10023  gid:10023 name:service.adb.tcp.port
[   27.389020@0] init: sys_prop: Unable to start service ctl [adbd] uid:10023 gid:10023 pid:2827
[   28.285508@0] init: untracked pid 2893 exited
[   31.375148@0] init: untracked pid 3056 exited
[   37.691146@2] init: sys_prop: permission denied uid:10023  gid:10023 name:persist.service.adb.enable
[   37.699242@2] init: sys_prop: permission denied uid:10023  gid:10023 name:service.adb.tcp.port
[   37.707388@3] init: sys_prop: Unable to start service ctl [adbd] uid:10023 gid:10023 pid:3456
[   39.615531@1] init: untracked pid 3554 exited
[   47.376325@0] init: untracked pid 3983 exited
[   47.769972@0] init: sys_prop: permission denied uid:10023  gid:10023 name:persist.service.adb.enable
[   47.778458@0] init: sys_prop: permission denied uid:10023  gid:10023 name:service.adb.tcp.port
[   47.790740@0] init: sys_prop: Unable to start service ctl [adbd] uid:10023 gid:10023 pid:4005
[   50.405438@0] init: untracked pid 4131 exited
[   57.910245@0] init: sys_prop: permission denied uid:10023  gid:10023 name:persist.service.adb.enable
[   57.917270@0] init: sys_prop: permission denied uid:10023  gid:10023 name:service.adb.tcp.port
[   57.925572@0] init: sys_prop: Unable to start service ctl [adbd] uid:10023 gid:10023 pid:4488
[   58.475999@1] init: untracked pid 4517 exited
[   66.465753@1] init: untracked pid 4852 exited
[   68.061021@0] init: sys_prop: permission denied uid:10023  gid:10023 name:persist.service.adb.enable
[   68.089450@0] init: sys_prop: permission denied uid:10023  gid:10023 name:service.adb.tcp.port
[   68.100525@0] init: sys_prop: Unable to start service ctl [adbd] uid:10023 gid:10023 pid:4923
[   69.485216@0] init: untracked pid 4990 exited
[   77.515356@0] init: untracked pid 5311 exited
[   78.141339@0] init: sys_prop: permission denied uid:10023  gid:10023 name:persist.service.adb.enable
[   78.148588@0] init: sys_prop: permission denied uid:10023  gid:10023 name:service.adb.tcp.port
[   78.160107@0] init: sys_prop: Unable to start service ctl [adbd] uid:10023 gid:10023 pid:5345
[   85.608720@0] init: untracked pid 5633 exited
[   88.254676@0] init: sys_prop: permission denied uid:10023  gid:10023 name:persist.service.adb.enable
[   88.261623@0] init: sys_prop: permission denied uid:10023  gid:10023 name:service.adb.tcp.port
[   88.270404@0] init: sys_prop: Unable to start service ctl [adbd] uid:10023 gid:10023 pid:5754
[   88.667809@1] init: untracked pid 5761 exited
[   96.684980@1] init: untracked pid 6066 exited
[   98.418150@0] init: sys_prop: permission denied uid:10023  gid:10023 name:persist.service.adb.enable
[   98.425683@0] init: sys_prop: permission denied uid:10023  gid:10023 name:service.adb.tcp.port
[   98.467319@0] init: sys_prop: Unable to start service ctl [adbd] uid:10023 gid:10023 pid:6159
sleep .......
step 1
enter ddr_self_refresh
CPU off...
CPU off done
CEC M8:uboot: P_AO_DEBUG_REG0:
00000000
n200C_pwm_set_vddEE_voltage
## VDDEE voltage = 0x035c
##### duty_high = 0x001c
##### P_PWM_PWM_D value = 001c0000
suspend stay 24M...


----------------------------------------
請問我家的無線網卡和有線網卡分別是哪個？

NadOo

我的環境是：ZTE B860A v1.0 成都電信，iTV采用DHCP方式連接；憑猜測加入了pppoe方式的支持，還請大家測試反饋；

NadOo

怎么腳本都被自動切的只剩下一行了..

NadOo

編輯了幾次，沒辦法直接顯示超過2行的代碼，不知道是不是權限不夠，不折騰了.

人見百態

這個厲害   正需要這個呢！ 感謝樓主的分享！

費老濕

強烈支持樓主ing……

hao501802766

感謝分享！

愛簡單3

高手??！贊

kozin

高手高手 佩服佩服

NadOo

這個腳本是在之前其它網友的腳本基礎上改進的，不需要手動填寫網關、DNS，都是自動獲取的。只是有個
itv_app=8 這個參數，需要大家自己根據情況修改，四川電信目前設置為8就可以了。